Mada za sehemu hiiPerforming PLC programmingMada 5
Performing Basic Sequence Circuits
A sequence circuit is an arrangement of control elements that operates equipment in a predetermined order, one step after another. In programmable logic controllers (PLCs), sequence circuits are created using ladder logic — a programming language that mimics the appearance of electrical relay diagrams. Understanding basic sequence circuits allows you to automate processes such as conveyor belts, pumping systems, and industrial machines.
All sequence circuits are built from three fundamental logic operations:
1.1 AND Logic
The output is ON only when all inputs are ON.
- Symbol: Two or more contacts in series
- Truth table:
Input A Input B Output 0 0 0 0 1 0 1 0 0 1 1 1
1.2 OR Logic
The output is ON when any input is ON.
- Symbol: Two or more contacts in parallel
- Truth table:
Input A Input B Output 0 0 0 0 1 1 1 0 1 1 1 1
1.3 NOT Logic
The output is ON when the input is OFF, and vice versa.
- Symbol: A normally closed (NC) contact
Ladder logic is the standard programming language for PLCs. It consists of:
- Rungs: Horizontal lines that represent control circuits
- Rails: Vertical lines on left (power) and right (neutral)
- Contacts: Represent inputs (switches, sensors)
- Coils: Represent outputs (motors, lights, solenoids)
Each rung is evaluated top to bottom and left to right by the PLC processor.
A sequence circuit operates equipment in steps. Each step must be completed before the next begins. The basic structure follows these steps:
- Identify inputs — sensors, switches, or push buttons that provide signals
- Identify outputs — motors, valves, or indicators that perform actions
- Determine the sequence — the order in which outputs must activate
- Write the ladder logic — using contacts and coils in the correct arrangement
- Test the program — simulate or run to verify correct operation
A small farm in Morogoro uses a PLC to control a water pump that fills a storage tank. The system must follow this sequence:
- Step 1: Start button (S1) is pressed
- Step 2: Pump motor (M) turns ON
- Step 3: When tank is full (level sensor LSF closes), pump turns OFF
Inputs and Outputs
| Tag | Description | Type |
|---|---|---|
| S1 | Start push button (NO) | Input |
| LSF | Level sensor (NO) | Input |
| M | Pump motor | Output |
Ladder Logic
|----[ ]----[ ]----( )----|
| S1 LSF M |
|------------------------|
|----[ ]----------------|
| LSF ( ) |
| (M) |
Explanation:
- Rung 1: When START (S1) is pressed AND level sensor (LSF) is open (tank not full), the pump coil (M) energizes and motor runs
- Rung 2: When LSF closes (tank becomes full), the NC contact opens, de-energizing coil M and stopping the pump
This creates a simple automatic fill sequence — the pump runs until the tank is full, then stops automatically.
In Tanzania, small-scale fish farmers in Lake Victoria use sequence circuits in simple PLC systems to control aerator pumps that add oxygen to fish ponds. When a timer or low-oxygen sensor signals the PLC, the aerator automatically turns on in sequence, keeping fish alive without requiring constant manual monitoring — this helps reduce fish mortality and increases earnings for farmers selling fresh fish at local markets like Mwanza.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment, and safety gear.
- Read and interpret operating manuals.
- Read and interpret circuit diagrams.
- Draw sequential and ladder logic diagrams.
- Read and interpret ladder programs.
- Observe safety precautions.
- Perform simulation.
- Upload ladder program.
- Connect PLC sensors and actuators.
- Perform functional tests.
- Adjust parameters for optimum performance.
- Document the installation.
- Clean tools, equipment, and the work place.
Tathmini ya matokeo
Installation of PLC system performed according to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to perform basic sequence circuits.
Principles: The student should explain principles related to performing basic sequence circuits.
Theories: The student should explain: -
- Types of PLC systems.
- Master slave configurations.
- Ladder programming.
- Uploading and downloading ladder programs.
- PLC Operations monitoring process.
- Sequence operators and function blocks.
- PLC firmware updates.
- Electronic devices.
- Measurements and instrumentation.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while installing the PLC system.
- Safe handling of work tools.
Swali
What must be true for the output to be ON in an AND logic circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado