Mada za sehemu hiiConstructing RLC circuitsMada 3
- Building a resistance and capacitance circuit
- Building a resistance and inductance circuit
- Building a resistance, capacitance and inductance circuit
Building a Resistance and Inductance (RL) Circuit

An RL circuit is an electrical circuit consisting of a resistor (R) and an inductor (L) connected together. The resistor limits the current flow, while the inductor stores energy in its magnetic field when current passes through it.
An inductor is a coiled wire that stores energy in a magnetic field when current flows through it. The ability of an inductor to store energy is called inductance, measured in Henry (H).
When RL elements are connected in series to a DC source:
- When the switch is closed, current begins to flow through the circuit
- The inductor creates a magnetic field that opposes changes in current
- Initially, the inductor resists current flow, so the lamp is dim
- Over time (approximately 5 time constants), the magnetic field builds up fully
- After this time, the inductor behaves like a short circuit (wire) — it no longer opposes current
- Only the resistor remains effective in limiting current
- The lamp gradually becomes brighter until it reaches full brightness
This behavior is called the charging phase of the inductor.
When RL elements are connected in parallel to a DC source:
- Both branches receive the full source voltage
- The inductor branch will eventually act as a short circuit
- This can cause the entire circuit to become shorted
- In practical terms, connecting an inductor in parallel with a DC source after it is fully charged can create a short circuit condition
Materials Required
- One inductor (e.g., 150mH or 470mH)
- One resistor or lamp (12V)
- Connecting wires
- Breadboard
- 12V DC power supply (or battery)
- Two-way switch (optional)
Implementation Steps
-
Prepare the circuit diagram — draw the RL series circuit showing the DC source, switch, resistor/lamp, and inductor connected in series
-
Select the components — choose an inductor with a suitable inductance value (such as 150mH) and a 12V lamp as the resistor
-
Connect the circuit — place the inductor, lamp, and switch on the breadboard or circuit board, then connect all components in series using connecting wires
-
Set the power supply — adjust the DC power supply to 12V and connect it to the circuit
-
Observe the behavior — close the switch and watch how the lamp brightness changes over time:
- Initially: dim light (inductor opposes current)
- After a few seconds: full brightness (inductor now acts as wire)
-
Clean the workplace — after completing the activity, disconnect the power and organize all components
Example Observation
When you connect a 12V lamp in series with a 470mH inductor to a 12V DC supply:
- The lamp will start with a dim light
- Gradually, the light becomes brighter
- After about 5 time constants, the lamp reaches full brightness
- This happens because the inductor initially opposes current flow, then acts as a short circuit once the magnetic field is fully established
- Always wear safety goggles and overalls when working with electrical circuits
- Ensure the power supply is turned off before making connections
- Do not leave the circuit connected for too long — the inductor may overheat
- Use insulated tools when working with live circuits
- Keep the work area clean and free of metal objects that could cause short circuits
- An inductor stores energy in its magnetic field
- In a DC circuit, an inductor initially opposes current flow (acting like an open circuit)
- After 5 time constants, an inductor behaves like a short circuit (wire) in DC
- The lamp brightness increases as the inductor "charges up"
- In series RL circuits, the same current flows through both components
In Tanzania, RL circuits are used in the ignition systems of motorcycles and small engines commonly found in rural areas. The inductor (coil) stores energy and then releases it as a high-voltage spark to ignite the fuel. When a mechanic tests or repairs these ignition coils, understanding how the inductor behaves in the circuit helps them diagnose faults — for example, if the spark is weak, the inductor may not be storing energy properly due to a damaged coil or incorrect resistance in the circuit.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a wiring diagram of the RL circuit.
- Identify equipment, tools, and materials required.
- Prepare resistor, capacitors, and cable for termination.
- Measure and record the RL parameters of the circuit.
- Observe safety precautions.
- Clean the work area, tools, and equipment.
Tathmini ya matokeo
RL circuit built as per electrical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to build a resistance and inductance circuit.
Principles: The student should explain the principles related to building a RL circuit.
Theories: The student should explain:
- The RL circuit and its behaviour.
- The uses of tools and equipment. Circumstantial Detailed knowledge about:
- Safety precautions when soldering the RC circuit.
- Properties of materials,
- hazards classifications, and controls
Swali
What is an RL circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado