Mada za sehemu hiiConstructing simple magnetic circuitsMada 3
- Constructing a circuit with a solenoid
- Constructing an electric bell
- Building a simple transformer
An electric bell is a device that produces a repetitive ringing or buzzing sound under the action of an electromagnet. It converts electrical energy into sound energy through rapid make-and-break of an electrical circuit.
An electric bell consists of the following main parts:
- Electromagnet – a coil of insulated copper wire wound around a soft iron core
- Armature – a thin soft iron strip attached to a springy steel strip
- Springy steel strip – a flexible arm that carries the clapper and completes the circuit
- Screw contact – a normally closed contact point that touches the armature
- Clapper (striker) – a metal piece that strikes the gong to produce sound
- Gong – a metal plate or cup that resonates when struck
- Power source – usually a battery (e.g., 6V or 12V)
- Switch – to turn the bell on and off
The electric bell operates on the principle of electromagnetism. Follow these steps:
-
Close the switch – This allows current to flow from the battery through the circuit.
-
Electromagnet energizes – Current flows through the coil, making the iron core magnetic. The core attracts the soft iron armature.
-
Armature moves – The armature is pulled toward the electromagnet, carrying the clapper with it. The clapper strikes the gong, producing a sound.
-
Circuit breaks – As the armature moves toward the electromagnet, the springy steel strip moves away from the screw contact, breaking the circuit.
-
Electromagnet de-energizes – With no current, the magnetic pull is lost.
-
Spring returns – The springy steel strip springs back to its original position, touching the screw contact and reconnecting the circuit.
-
Cycle repeats – This rapid make-and-break happens continuously as long as the switch is closed, causing repeated strikes on the gong and a continuous ringing sound.
Tools and Materials Needed
- Combination pliers, electrician's knife, measuring tape, claw hammer, screwdrivers
- Electric bell wiring diagram
- Power source (battery)
- Electromagnet (coil wound on iron core)
- Clapper and gong (or metal plate)
- Spring contact arm
- Insulated copper wire
- Switch
- Screws
- Wooden or plastic base
- Personal Protective Equipment (PPE)
Construction Steps
-
Wear appropriate PPE and prepare your work area.
-
Study the circuit/wiring diagram to understand the connections.
-
Prepare the electromagnet by winding insulated copper wire into a coil around a soft iron core.
-
Mount the electromagnet onto a wooden or plastic base using screws or adhesives.
-
Install the armature (thin iron strip) near the electromagnet, ensuring a small gap between them.
-
Set up the contact point by placing a metal contact screw so that it lightly touches the armature.
-
Complete the circuit by connecting the battery, switch, and all components according to the wiring diagram. Do not power the circuit yet.
-
Ask your teacher to inspect your circuit for correctness and safety.
-
Test the constructed electric bell by closing the switch. The bell should ring continuously.
-
Turn off the circuit, pack tools, and clean the work area.
- Use insulated wires and ensure all connections are secure to prevent short circuits and electric shock.
- Always disconnect the power supply before working on the circuit.
- Double-check all connections against the wiring diagram before powering.
- Avoid using damaged components.
- Never touch the gong or clapper while the bell is ringing.
To increase the volume of an electric bell:
- Use a larger gong – A bigger metal plate or cup produces a louder sound.
- Increase the number of turns on the coil – This makes the electromagnet stronger, causing a harder strike.
- Position the armature closer to the electromagnet – This increases magnetic attraction and strike force.
- Use a stronger power source – A higher voltage increases the current, making the magnet stronger.
The electromagnet and armature must be positioned close to each other but not touching because:
- To allow movement – The armature needs space to move toward the electromagnet when energized.
- To create the make-and-break action – When the armature moves, it must separate from the contact screw to break the circuit. If they touched, the circuit would remain closed continuously, and the bell would not ring.
- To prevent short circuit – Direct contact could cause short-circuiting and damage the battery.
Question: An electric bell is connected to a 12V battery. The coil has a resistance of 20Ω. Calculate the current flowing through the circuit when the switch is closed.
Solution:
Using Ohm's Law: V=I×R
Rearranging to find current: I=RV=20Ω12V=0.6A
The current flowing through the circuit is 0.6 amperes.
Electric bells are used in:
- Doorbells – Residential buildings to signal visitors
- School bells – To mark class changes
- Alarm systems – Fire and security alarms
- Industrial signaling – Warning and alert systems in factories
In Tanzania, electric bells are commonly used as doorbells in homes and schools. For example, a small electrical shop in Arusha might install a self-constructed electric bell at the entrance to alert the shopkeeper when a customer arrives, using locally available materials like iron nails for the core and copper wire from rewound motors. This practical skill can also lead to small business opportunities repairing doorbells and simple alarm systems in the community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment, and safety gear.
- Design a circuit diagram of an electric bell.
- Wind a coil around an iron core.
- Connect an electric bell to an electric power.
- Solder the built circuits.
- Measure and record the parameters of the circuits.
- Apply safety precautions.
- Clean work area, tools, and equipment.
Tathmini ya matokeo
Electric bells are constructed per IEE regulations and measured parameters conform to IEE regulations and standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct an electric bell.
Principles: The student should explain the principles related to constructing an electric bell.
Theories: The student should explain:
- The types of electric bells.
- The difference between a bell and a buzzer.
Detailed knowledge about:
- Safe handling of power. circuits
- Properties of dielectric materials
- Precautions to be taken when working on capacitive circuits.
Swali
What is the function of the springy steel strip in an electric bell?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado