Mada za sehemu hiiConstructing simple filter circuitsMada 3
- Constructing a single-pole RC filter
- Building a passive LC filter
- Building an RLC filter
A passive LC filter is an electronic circuit made from inductors (L) and capacitors (C) that allows certain AC signal frequencies to pass while blocking others. Unlike active filters, it needs no external power source — it uses only passive components.
A passive LC filter is a frequency-selective circuit built using only inductors and capacitors connected together. It works by storing and releasing electrical energy in magnetic fields (inductor) and electric fields (capacitor). When AC signals of different frequencies pass through, these components react differently depending on the frequency, allowing some frequencies through and stopping others.
Key terms:
- Inductor (L) — stores energy in a magnetic field; opposes changes in current; blocks high frequencies
- Capacitor (C) — stores energy in an electric field; opposes changes in voltage; blocks low frequencies
- Cut-off frequency — the frequency at which the filter starts to block signals
The opposition of an inductor or a capacitor to alternating current is called reactance. It is measured in ohms (Ω).
- Inductive reactance: XL = 2 × π × f × L. It rises as the frequency rises, so an inductor passes low frequencies easily and opposes high frequencies.
- Capacitive reactance: XC = 1 ÷ (2 × π × f × C). It falls as the frequency rises, so a capacitor opposes low frequencies and passes high frequencies easily.
Here f is the frequency in hertz (Hz), L is the inductance in henrys (H) and C is the capacitance in farads (F).
For a filter made of one inductor and one capacitor, the cut-off frequency is:
fc = 1 ÷ (2 × π × √(L × C))
There are four main types you need to identify:
1. Low-Pass Filter (LPF)
Allows frequencies below the cut-off frequency to pass through and blocks frequencies above it.
Circuit: Inductor in series with the signal path, and capacitor connected across the output.
Input → L (in series) → output, with C from the output to the common (return) line
The inductor opposes high frequencies and the capacitor short-circuits what is left of them to the common line, so only low frequencies reach the output.
2. High-Pass Filter (HPF)
Allows frequencies above the cut-off frequency to pass through and blocks frequencies below it.
Circuit: Capacitor in series with the signal path, and inductor connected across the output.
Input → C (in series) → output, with L from the output to the common line
The capacitor opposes low frequencies and the inductor short-circuits what is left of them, so only high frequencies reach the output.
3. Band-Pass Filter (BPF)
Allows only a specific range of frequencies (between two cut-off frequencies) to pass through.
Circuit: Inductor and capacitor in series with each other, placed in the signal path.
Input → L → C → output
At one frequency, called the resonant frequency, the reactances of L and C cancel each other. The pair passes that frequency and a narrow band around it, and opposes all others.
4. Band-Stop Filter (BSF) / Notch Filter
Blocks a specific range of frequencies and allows all others to pass.
Circuit: Inductor and capacitor in series with each other, connected across the output (from the signal line to the common line).
At the resonant frequency the series pair has almost no opposition, so it short-circuits that frequency to the common line. Other frequencies pass to the output.
Tools and Equipment Needed
- Combination pliers
- Electrician's knife
- Measuring tape
- Set of screwdrivers
- Soldering iron with stand, and solder
- Multimeter, and a low-voltage signal generator or other low-voltage AC source
- Leather gloves, overalls, safety boots, safety goggles
Safety First
Before starting any construction work:
- Wear leather gloves, overalls, safety boots, and safety goggles
- Ensure your work area is clean and dry
- Check that all tools are in good condition
- Never work on live circuits, and never connect a filter you have built to the mains. Test it only from a low-voltage source of not more than 12 V
- Use a non-polarised capacitor. A polarised (electrolytic) capacitor connected to alternating current can overheat and burst
- A capacitor can hold a charge, and an inductor gives a voltage pulse when its current is suddenly interrupted. Switch off the source before changing connections, and discharge large capacitors through a resistor before touching them
- Rest the soldering iron on its stand, never touch the tip, solder where there is fresh air and wash your hands afterwards. Do not overheat an inductor when soldering, because too much heat damages the enamel on its windings
Construction Steps
Step 1: Plan the circuit Decide which type of filter you need based on the frequency range you want to allow or block. Draw the circuit diagram, showing the input terminals, the inductor, the capacitor, the output terminals and the common line.
Step 2: Gather components Collect the appropriate inductor and capacitor values for your desired cut-off frequency. For a first practical, a 100 mH inductor and a 10 µF non-polarised capacitor give a cut-off of about 159 Hz, which is low enough to measure with an ordinary multimeter.
Step 3: Prepare conductors Use the measuring tape to measure and cut connecting wires to the required lengths. Strip wire ends using the electrician's knife — about 1 cm of insulation should be removed.
Step 4: Connect the inductor and capacitor Using combination pliers, twist and connect the component leads securely:
- For a low-pass filter: connect the inductor in series between the input and output terminals, and the capacitor across the output terminals
- For a high-pass filter: connect the capacitor in series and the inductor across the output terminals
Then solder each joint. Heat the joint with the tip of the iron, feed in the solder until it flows, and let the joint cool without moving it. A good joint is bright and smooth.
Step 5: Secure all connections Use screwdrivers to tighten any terminal screws. Ensure no bare wires are touching each other accidentally.
Step 6: Test the circuit Connect the input to the low-voltage signal generator and the output to a load resistor. Set the multimeter to AC voltage. At several frequencies below and above the cut-off frequency, measure the input voltage and the output voltage, and record them in a table with the columns: frequency, input voltage, output voltage. For a low-pass filter the output voltage is close to the input voltage at low frequencies and falls as the frequency rises above the cut-off.
Step 7: Clean and store Switch off and disconnect the source. Unplug the soldering iron and let it cool on its stand. Collect wire offcuts and solder scraps and put them in the waste bin, wipe the bench, and return the tools, meters, safety gear and unused components to their places.
Problem: A student in a workshop in Arusha builds a low-pass filter with a 100 mH inductor in series and a 10 µF non-polarised capacitor across the output, and tests it from a 6 V signal generator. Find the cut-off frequency, and the reactance of each component at 50 Hz and at 500 Hz.
Solution:
-
Convert the values: L = 100 mH = 0.1 H and C = 10 µF = 0.00001 F.
-
Cut-off frequency: L × C = 0.1 × 0.00001 = 0.000001, and √0.000001 = 0.001. So fc = 1 ÷ (2 × 3.142 × 0.001) = 1 ÷ 0.006284 ≈ 159 Hz.
-
At 50 Hz: XL = 2 × 3.142 × 50 × 0.1 ≈ 31.4 Ω, and XC = 1 ÷ (2 × 3.142 × 50 × 0.00001) = 1 ÷ 0.003142 ≈ 318 Ω.
-
At 500 Hz: XL = 2 × 3.142 × 500 × 0.1 ≈ 314 Ω, and XC = 1 ÷ (2 × 3.142 × 500 × 0.00001) = 1 ÷ 0.03142 ≈ 31.8 Ω.
Result: At 50 Hz, below the cut-off, the series inductor has a low reactance and the capacitor across the output has a high reactance, so the signal reaches the output. At 500 Hz, above the cut-off, the inductor has a high reactance and the capacitor a low one, so most of the signal is stopped. The filter passes low frequencies and blocks high ones.
When examining an existing LC filter circuit, look for these clues:
| Circuit Arrangement | Filter Type |
|---|---|
| Inductor in series, capacitor across the output | Low-pass |
| Capacitor in series, inductor across the output | High-pass |
| L and C in series with each other, in the signal path | Band-pass |
| L and C in series with each other, across the output | Band-stop |
In Tanzania, passive LC filters are used in radio receivers found in rural homes and vehicles to select the correct broadcast station from many frequencies travelling through the air. A technician building a simple FM receiver circuit would use a band-pass filter to allow only the FM radio frequencies (88–108 MHz) to reach the amplifier, blocking unwanted signals like AM broadcasts or electrical interference. This same principle applies to filtering unwanted noise in audio equipment shops in Dar es Salaam or Moshi, ensuring clear sound quality for customers.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear.
- Design a circuit diagram of the filter circuit.
- Build a low pass filter circuit (LC).
- Solder the built circuits.
- Measure and record the parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment and safety gear.
Tathmini ya matokeo
Passive LC filter circuits are constructed as per IEE regulations and the test results conform to approved standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct a single-pole LC filter.
Principles: The student should explain the principles related to building a passive LC filter.
Theories: The student should explain:
- Behaviour of inductance in ac circuits.
- Behaviour of capacitance in ac circuits.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precaution on inductive load charges.
- Safety precaution when soldering the inductors.
- Safe handling of working tools, equipment and inductors.
Swali
Which component in a passive LC filter stores energy in a magnetic field?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado