Mada za sehemu hiiInstalling water distribution mainsMada 3
- Drilling and tapping from the water mains
- Installing service pipe
- Fixing water meters
Drilling and Tapping from the Water Mains
When a new building, school, or community needs to be connected to the public water supply, plumbers must create a connection to the existing water main without interrupting service to other users. This is done through drilling and tapping — two essential skills in water supply installation that allow new pipes to be added to pressurised water mains safely.
Drilling is the process of making a clean, accurate hole in a water main pipe using a special drill. This hole is created while the water main is still full of water and under normal operating pressure.
Tapping is the process of creating internal threads inside the drilled hole, so that a new pipe or fitting can be securely attached to the water main.
These two steps are performed together using a special tapping machine and fitting. The process allows workers to connect new service pipes without shutting off the water supply to existing customers.
Drilling and tapping into water mains is important for several reasons:
-
Continuous service: New connections or repairs can be made without interrupting water supply to customers. This is essential in areas where uninterrupted service is necessary, such as hospitals, schools, and markets.
-
Reduced downtime and costs: Tapping significantly reduces the time and money needed for excavation, labour, and potential damage to the water system.
-
Water quality and safety: Keeping the water main under pressure during tapping prevents contamination and maintains consistent water quality.
-
Network expansion: Tapping enables the water supply network to grow and serve new customers without major disruptions.
-
Improved customer satisfaction: By minimising service interruptions, tapping leads to higher customer satisfaction and a more reliable water supply.
There are two main methods used to tap into water mains:
Wet Tapping
Wet tapping is the process of connecting a new pipeline to an existing pressurised water main without shutting down the water supply. This method is crucial for expanding and maintaining water supply networks, especially in urban areas where service interruptions must be minimised.
Risks associated with wet tapping include:
- Contamination risk if proper procedures are not followed
- Structural failure if cutting is done imprecisely
- Equipment malfunction from improper handling
- Personnel injury from pressurised water or cutting tools
- Possible service disruption from poor performance
Hot Tapping
Hot tapping is the ability to safely tie into a pressurised system by drilling or cutting while it is operating and under pressure. It involves placing a tapping fitting onto a water main, along with a gate or ball valve that controls water flow. The water stream remains under pressure without interrupting or emptying the pipe section, allowing maintenance or modifications while the pipeline continues operating.
The following tools and equipment are required for drilling and tapping:
- Hot tapping machines: Specialised drilling machines (manual or electric) designed to drill holes into pressurised water mains
- Tapping saddles or sleeves: Fittings that attach to the water main and provide a connection point for the new branch pipe
- Pilot drill bits: Specialised drill bits that create a pilot hole for accurate hole creation
- Valves: Gate or ball valves to isolate the section being tapped and control water flow
- Pipes and fittings: Service pipes and appropriate fittings for the connection
- Personal protective equipment (PPE): Safety goggles, gloves, safety boots, and hard hat
When drilling and tapping a water main, always follow these safety measures:
- Wear appropriate PPE — including safety goggles, gloves, flame-resistant clothing, and helmets
- Monitor system pressure — closely watch and regulate pressure during the tapping process
- Secure the site — prevent unauthorized access and be aware of underground utilities
- Have an emergency response plan — be prepared for unforeseen situations
- Follow manufacturer instructions — use equipment correctly and maintain it properly
- Work with qualified personnel — ensure experienced workers perform the procedure
The following steps outline how to tap from a water main:
-
Excavation: Carefully dig a hole using a shovel until the water pipe is visible. Clean the pipe thoroughly with a cloth.
-
Fix the tapping sleeve: Attach the tapping sleeve firmly around the main water pipe.
-
Attach the valve: Connect the control valve to the tapping sleeve so water can be turned on and off.
-
Drill the hole: Use the hot tapping machine to make a hole in the main pipe through the valve.
-
Connect the service pipe: Attach the new service pipe to the valve and tighten all joints securely.
-
Seal threads: Wrap plumber's tape (Teflon tape) on every threaded connection to prevent water leaks.
-
Test for leaks: Turn on the valve slowly and check if there are any leaks at the connections.
-
Backfill: If no leaks are found, cover the pipe back with soil and level the ground.
-
Clean and store: Wash and properly store all tools and safety equipment.
-
Report: Document and share what was learned with classmates and submit work to the teacher.
A plumber needs to connect a new classroom block at a secondary school in Dar es Salaam to the municipal water main. The water main has a diameter of 150 mm and operates at a pressure of 5 bar.
Solution:
-
First, the plumber excavates to expose the water main at the connection point.
-
A tapping sleeve (150 mm) is fitted around the main pipe and secured with bolts.
-
A gate valve is attached to the tapping sleeve.
-
Using a hot tapping machine, a 25 mm hole is drilled through the valve into the water main.
-
The drill is removed and the valve is closed.
-
A 25 mm service pipe is connected to the valve using plumber's tape on all threaded joints.
-
The valve is slowly opened to supply water to the new classroom block.
-
The plumber checks for leaks and backfills the trench if everything is secure.
This process allows the school to receive water without interrupting supply to neighboring buildings.
Drilling and tapping are essential skills for connecting new buildings to existing water mains. The process involves making a hole in a pressurised pipe while it remains in service, using specialised equipment and following strict safety procedures. By mastering this technique, plumbers can expand water supply networks efficiently while maintaining continuous service to all customers.
In Tanzania, when a new shop or restaurant is built in towns like Arusha, Mwanza, or Dodoma, the owner must request a water connection from the local water authority. A qualified plumber performs drilling and tapping to connect the new building's service pipe to the municipal water main under the road. This allows the business to receive clean water for cooking, cleaning, and sanitation without disrupting water supply to neighboring shops and homes, supporting daily commercial activities across Tanzanian towns.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawing.
- Identify the size of distribution mains.
- Identify pipe materials for distribution mains
- Classify pipes for distribution mains (HDP, LDP)
- Identify tools fittings to perform distribution mains
- Excavate trench
- Re-back filling the trench
- Test
- Clean the work place
- Clean tools, equipment and store in a safe place
Tathmini ya matokeo
Drilling and tapping from water main were performed correctly
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain: -
- Drilling and tapping from the water main.
Principles: The student should explain the principles of: -
- Classifying pipes for distribution mains.
Theories: The student should explain: -
- Types of distribution system.
- All fittings fixed in the distribution main.
- Joining techniques.
- The differences between tapping under pressure and non-pressure
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while drilling and tapping from water main.
- Environmental issue
- First aid
Swali
What is the main purpose of drilling and tapping when connecting a new building to the water main?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado