Mada za sehemu hiiPerforming water treatmentMada 5
Performing Chlorination
Chlorination is a water treatment process that involves adding chlorine or chlorine-based chemicals to water to kill or inactivate harmful microorganisms such as bacteria, viruses, and protozoa. This process makes water safe for drinking, household use, and industrial applications. The main goal of chlorination is to eliminate pathogens and protect public health from waterborne diseases like cholera, dysentery, and typhoid.
Chlorine Demand
Chlorine demand refers to the amount of chlorine used to remove impurities, microorganisms, and other unwanted substances in the water before a protective residual remains. Before applying chlorine, it is essential to assess the water's quality by checking turbidity, pH, and the presence of organic matter, as these factors affect the amount of chlorine required.
Residual Chlorine
After chlorination, a small amount of chlorine is left in the water called residual chlorine. This leftover chlorine stays in the water as protection and continues killing bacteria and other harmful pathogens. It works by slowly reacting with any new contaminants that enter the water, keeping it safe during storage and distribution.
Contact Time
Chlorine must be thoroughly mixed into the water and allowed sufficient contact time—at least 30 minutes—to work effectively. This gives the chlorine enough time to react with and eliminate harmful microorganisms.
The effectiveness of chlorination depends on several factors:
-
pH of the water: Chlorine's effectiveness depends on pH. At lower pH (acidic conditions), chlorine exists mainly as hypochlorous acid (HOCl), which is a stronger disinfectant. At higher pH (alkaline conditions), it forms hypochlorite ions (OCl⁻), which are less effective. The optimal pH range is 6.5 to 7.5.
-
Water temperature: Warmer water speeds up the reaction between chlorine and microorganisms, improving disinfection efficiency. Colder water slows these reactions, making chlorination less effective.
-
Chlorine dosage: The dose must be carefully calculated based on the volume and quality of the water. It must be high enough to kill pathogens but not excessive to cause harmful byproducts or unpleasant taste and smell.
-
Contact time: Longer contact time allows chlorine to act more thoroughly on microorganisms, but overly long exposure may cause taste and odour problems.
-
Water quality and impurities: Organic matter, ammonia, and other impurities react with chlorine and reduce its availability for disinfection. More contaminated water requires more chlorine.
-
Chlorine residual: Maintaining an appropriate residual ensures continued protection during storage and distribution. However, excessive residual can lead to undesirable tastes, odours, or health concerns.
The chlorination process follows these sequential stages:
-
Water quality assessment: Analyse pH, temperature, turbidity, and the presence of organic matter or other contaminants.
-
Chlorine dose calculation: Determine the appropriate chlorine dosage based on water quality assessment results.
-
Chlorine application: Add chlorine or chlorine-based compounds (sodium hypochlorite or calcium hypochlorite) to the water.
-
Mixing: Thoroughly mix the water to ensure even distribution of chlorine throughout.
-
Contact time: Hold the chlorinated water in a contact tank or basin for typically 30 minutes to 1 hour.
-
Monitoring chlorine residual: Check chlorine residual levels to ensure adequate disinfectant remains.
-
pH adjustment (if needed): Adjust pH to maintain chlorine in the effective form of hypochlorous acid (HOCl).
-
Post-chlorination treatment: Further treat the water to reduce residual chlorine if necessary, using filtration or activated carbon.
-
Final water quality check: Verify that the treated water meets safety standards before distribution.
Requirements
- Raw water
- Personal Protective Equipment (PPE)
- Chlorine (sodium hypochlorite)
- Plastic box
- Stopwatch
- Beaker
- pH meter
- Thermometer
- Stirring stick
Procedure
- Collect raw water from a nearby river or water source.
- Using a beaker, take a sample and measure its temperature with a thermometer. Record the reading.
- Measure the pH of the water using a calibrated pH meter. Record the value.
- Use the recorded temperature and pH readings to determine the appropriate chlorine dosage based on water quality.
- Pour a measured volume of water into a clean plastic box, filling it to about three-quarters of its capacity.
- Add the calculated amount of chlorine to the water. Stir thoroughly using the stick for 30 to 60 seconds to ensure uniform mixing.
- Allow the chlorinated water to stand undisturbed for at least 1 hour to ensure effective disinfection. Use the stopwatch to track the time.
- Re-measure the pH of the treated water. Ensure the final pH is within the acceptable range of 6.5 to 8.5 for drinking water quality.
- Clean and store equipment and tools in a safe place.
- Write a report and submit it to your teacher for assessment.
Safety Precautions
- Use PPE to protect skin, eyes, and lungs from harmful exposure.
- Be aware that chlorine is toxic, corrosive, and highly flammable.
- Avoid mixing chlorine with other chemicals like acids, as this can produce dangerous gases or explosions.
- Avoid skin and eye contact—direct contact can cause burns, irritation, or permanent damage.
- Work in a ventilated area to prevent inhalation of toxic fumes.
Worked Example
A student collects 5 litres of raw water from a local river. The water has a temperature of 25°C and pH of 7.0. Based on the water quality:
- The pH of 7.0 is within the optimal range (6.5–7.5), so the chlorine will work effectively as hypochlorous acid.
- At 25°C, the water is warm enough for good disinfection efficiency.
- The student calculates a chlorine dosage of 2 mg/L (standard for moderately clean water).
- For 5 litres: 2 mg/L × 5 L = 10 mg of chlorine needed.
- The student adds the equivalent amount of sodium hypochlorite solution, stirs for 45 seconds, and allows 30 minutes contact time.
- After treatment, the residual chlorine is checked to ensure ongoing protection.
In Tanzania, chlorination is used by local water authorities like DAWASCO (Dar es Salaam Water and Sewerage Corporation) to disinfect treated water before supplying it to homes and businesses. A plumber or pipefitter working in a rural village might need to chlorinate water from a borehole or rainwater harvesting tank to make it safe for drinking, especially during cholera outbreaks or when the water source has been contaminated. This ensures that households receive water that meets the national drinking water standards and reduces the risk of waterborne diseases.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare chlorine
- Apply chlorine
- Determine PH.
- Clean instrument
- Sterilize instruments
- Store the instrument in a safe place
Tathmini ya matokeo
Chlorination performed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of:
- Performing chlorination.
Principles: The student should explain the principles of: -
- Disinfection/chlorination.
Theories: The student should explain: -
- Types of chemicals used.
- Clean tools and equipment
- Water quality
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing chlorination
- First aid
- Environmental requirements
Swali
What is the main purpose of leaving residual chlorine in treated water?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado