Mada za sehemu hiiConstructing hand drilled shallow wellsMada 4
Boring is the process of drilling or excavating a vertical hole into the ground to reach underground water for constructing a shallow well. In hand-drilled shallow well construction, boring creates the well shaft through which water can be extracted. This technique is commonly used in rural Tanzania where mechanical drilling equipment is not available.
Before starting any boring activity, ensure all the following tools and equipment are available:
- Tripod – provides support and height for the drilling operation
- Drill bits – cutting tools that penetrate different soil layers
- Auger bit – spiral-shaped bit for removing loose soil
- Riverside auger (conical auger) – cone-shaped auger for penetrating hard soil
- Extension rods – extend the drilling depth as needed
- Cross-piece handle – manual handle for rotating the drill
- Bailers – remove water and loose material from the hole
- Casing – pipe that prevents the well walls from collapsing
- Filter pipe – perforated pipe that allows water to enter the well
- Casing clamp and casing hanger – hold the casing in place
- Steel foot plates – provide stable base support
- Tape measure – measures depth and distances
- Chain spanner – tightens and loosens connections
Always wear the following safety gear before performing boring:
- Safety boots
- Helmet
- Overall
- Grooves (gloves)
1. Site Selection and Preparation
- Choose a suitable location away from sources of contamination such as latrines or garbage pits
- Clear the area of vegetation and debris
- Mark the center point of the proposed well
2. Setting Up the Rig
- Position the tripod over the marked center point
- Attach the steel foot plates to stabilize the tripod legs
- Ensure the setup is level and stable
3. Starting the Borehole
- Attach the appropriate drill bit (auger bit for soft soil or conical auger for harder soil) to the first extension rod
- Connect the cross-piece handle to the top of the rod assembly
- Lower the assembly into position at the center point
4. Drilling Operation
- Two or more workers stand on opposite sides of the cross-piece handle
- Apply downward pressure while rotating the handle in a clockwise direction
- Continue drilling until reaching the desired depth (usually 5–15 meters for shallow wells)
- Add additional extension rods as the depth increases
- Periodically remove the assembly to clear loose soil from the auger
5. Installing the Casing
- Once the desired depth is reached, lower the casing into the borehole
- Use the casing clamp and casing hanger to hold it securely
- Ensure the casing extends above ground level to prevent surface contamination
6. Installing the Filter Pipe
- Insert the filter pipe inside the casing
- Position the perforated section at the water-bearing soil layer
- The filter allows water to enter while blocking soil particles
7. Final Cleaning
- Use bailers to remove any remaining loose material
- Test the well by bailing out water to check flow rate
- Always wear PPE (helmet, safety boots, overall, and gloves)
- Check all equipment for defects before use
- Ensure the tripod is stable and securely positioned
- Keep hands away from moving parts during rotation
- Work in teams—never perform boring alone
- Take regular breaks to prevent fatigue
- Keep the work area clean and free of tripping hazards
A community in a village near Morogoro needs a shallow well for domestic water supply. The soil is soft and sandy, and the water table is approximately 8 meters deep.
Procedure followed:
- The team selected a site 15 meters away from the nearest latrine
- They set up the tripod and attached the auger bit
- Workers rotated the cross-piece handle while applying downward pressure
- They added extension rods as the hole deepened
- At 8 meters, they reached the water-bearing soil
- They installed the casing and filter pipe
- After cleaning with bailers, the well produced clean water
This well now serves approximately 20 households with safe drinking water.
In many rural villages across Tanzania, hand-drilled shallow wells are the primary source of clean water. A village near Mbeya might use the boring technique to construct a well that provides water for drinking, cooking, and small-scale irrigation. Local plumbers and community members with this skill can help reduce waterborne diseases by providing access to safe groundwater, and they can earn income by offering well-construction services to neighboring communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Clear site
- Lay out construction site
- Perform boring
- Clean tools and work area
- Keep tools at a safety place
Tathmini ya matokeo
Boring performed conforms to given technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain procedures of:
- Performing boring.
Principles: The student should explain the principle of: -
- Performing boring.
Theories: The student should explain: -
- Location of bore hole.
- How to establish location of bore hole.
- Bailing techniques.
- Preparation for bailing.
- Estimate the cost of labour and materials.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing boring pump
- Environmental requirements
- First aid
Swali
Which tool is used to remove loose soil from the borehole during drilling?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado