Mada za sehemu hiiPerforming manual thread cuttingMada 2
- Tapping a drilled hole
- Die threading a round bar
Tapping a drilled hole is the process of cutting internal threads inside a pre-drilled hole using a specialized tool called a tap. This creates a threaded hole that can accept a bolt or screw, allowing parts to be joined together securely.
A tap is a hardened steel tool used for cutting internal threads in a drilled hole. It is held and turned using a tap wrench. Taps are made from high carbon steel or high-speed steel (HSS) and come in sets of three:
- Taper tap – Has 7 to 10 chamfered threads. It is used for starting the thread and for through holes.
- Plug tap – Has 3 to 5 threads chamfered. It is used for general-purpose tapping.
- Bottoming tap – Has only 1 thread chamfered. It is used for tapping blind holes (holes that do not go through the material).
A tap wrench is a hand tool used to hold and turn taps. There are two main types:
- Double-end adjustable wrenches – Can hold taps of different sizes.
- T-handle wrenches – Provide better leverage for turning taps.
Step 1: Drill the Hole First
Before tapping, you must drill a hole of the correct size. The hole must be slightly smaller than the bolt you intend to use. For example, if you are tapping for an M8 bolt (8 mm diameter), you need to drill a hole with the appropriate drill bit size.
Step 2: Select and Prepare Tools
Gather all required tools and equipment:
- Tap of the correct size
- Tap wrench
- Drill and drill bit
- Lubricant (cutting oil)
- Try square (for alignment)
- PPE (safety glasses, gloves)
- Brush for cleaning chips
Step 3: Fix the Tap in the Wrench
Insert the tap into the tap wrench and tighten securely. Make sure the tap is held firmly to prevent it from slipping while turning.
Step 4: Align the Tap
Align the tap perpendicular to the hole using a try square. This ensures the threads are cut straight and will accept the bolt properly.
Step 5: Perform Tapping
Apply lubricant (cutting oil) to the tap and the hole. Turn the tap wrench clockwise to cut the threads. Follow these important rules:
- Turn forward about half a turn, then turn back slightly to break the chips
- Keep the tap perpendicular to the work
- Apply lubricant regularly to reduce friction and heat
Step 6: Clean the Threads
After tapping, remove the tap carefully. Clean out the metal chips (swarf) from both the tap and the threaded hole using a brush.
Step 7: Check the Thread
Check the quality of the thread using a plug gauge (for internal threads). The gauge should fit snugly into the threaded hole without force.
Question: You need to tap a hole for an M8 bolt. What size tap should you use, and what is the appropriate drill bit size for prior drilling?
Answer: For an M8 bolt, you use an M8 tap. The appropriate drill bit size is typically 6.8 mm or 6.9 mm. This creates a hole slightly smaller than 8 mm, allowing the tap to cut threads that will accept the M8 bolt.
For Taps:
- Clean the tap after each use to remove metal chips and cutting fluids
- Apply cutting fluid or lubricant while tapping
- Store taps in a dry, cool place to prevent rust
- Inspect regularly for dull edges or chipped teeth
For Tap Wrenches:
- Clean after each use
- Ensure correct adjustment to fit the tap size
- Lubricate moving parts
- Store in a dry environment
- Inspect and repair any damaged parts
In Tanzania, tapping a drilled hole is used when repairing broken water pipes or installing new plumbing fixtures. For example, when fixing a leaking pipe joint in a house, a plumber may need to tap a hole to secure a fitting with a bolt. This skill is also essential when assembling metal gates, building structures, or repairing farm equipment like water pumps in rural areas.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings.
- Select materials.
- Select tap.
- Select drill bits.
- Mark work piece.
- Clamp work piece
- Determine tapping direction
- Drill and chamfer the hole
- Perform internal threading
- Check the accuracy of threads
- Clean machine and tools
- Clean work place
- Store machine and tools in safe custody.
Tathmini ya matokeo
Internal threads made correctly as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedure of:
- Tapping a drilled hole.
Principles: The student should explain principles of:
- Tapping a drilled hole
Theories: The student should explain: -
- Main parts of taps
- Categories of taps
- Types of threads
- Function of threads.
- Calculation of Tap Drill Size (T.D.S
Detailed knowledge about:
- Safety precautions while tapping a drilled hole
- Waste disposal
- First aid
Swali
Which of the following is NOT a type of tap used for internal thread cutting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado