Mada za sehemu hiiBending pipesMada 6
Constructing Obtuse Bend in Pipe Fitting
An obtuse bend is a pipe bend that forms an angle greater than 90° but less than 180°. In plumbing and pipe fitting, bends are used to change the direction of pipe runs while maintaining smooth water flow. Common obtuse angles include 110°, 120°, and 135°. Unlike sharp bends, obtuse bends reduce flow resistance and prevent excessive stress on the pipe material.
Obtuse bends serve several essential purposes in plumbing systems:
- Direction changes: They allow pipes to navigate around obstacles in buildings
- Flow efficiency: Wider angles minimize pressure loss and turbulence
- Pipe protection: They reduce stress on pipe walls, preventing cracks and leaks
- Accessibility: They provide space for maintenance and valve installation
- Aesthetic routing: They enable cleaner pipe installations along walls and ceilings
1. Hydraulic Bending Machine Method
This is the most common and professional method for bending steel pipes. The machine uses hydraulic pressure to bend the pipe around a former (die) to the desired angle.
2. Spring Bending Method
A spring is inserted inside the pipe to support the walls during bending. This method is suitable for thin-walled pipes and smaller diameters.
3. Sand Filling Method
The pipe is filled with dry sand and capped at both ends before heating and bending. The sand supports the pipe interior and prevents collapsing.
- Steel pipe (appropriate diameter for the job)
- Hydraulic bending machine
- Bending dies (formers) of correct size
- Measuring tape
- Chalk or marker
- Pipe cutter
- Spring (for spring bending method)
- Personal Protective Equipment (PPE): gloves, safety boots, goggles
Step 1: Planning and Measurement
- Read and interpret the technical drawing or specification
- Measure the exact length of pipe required
- Determine the exact angle of the obtuse bend (e.g., 110°, 135°)
- Mark the bending point clearly with chalk on the pipe surface
Step 2: Selecting Equipment
- Choose the correct bending die (former) for the pipe diameter
- Check that the hydraulic bending machine is in good working condition
- Verify all safety guards are in place
Step 3: Setting Up the Machine
- Secure the pipe in the bending machine's clamping mechanism
- Align the marked bending point with the machine's pivot point
- Set the angle stop to the desired obtuse angle
Step 4: Performing the Bend
- Operate the hydraulic lever slowly to apply force
- Continue bending until the pipe reaches the set angle
- Avoid over-bending by checking the angle regularly
Step 5: Inspection and Finishing
- Release the clamp and remove the bent pipe
- Check for any cracks, wrinkles, or flattening
- Measure the angle to confirm it meets specifications
- Clean the pipe and store properly
A plumber needs to create a 135° bend in a steel pipe to route water around a corner in a house. The pipe diameter is 15 mm.
Calculation: If the pipe length from the corner is 300 mm, the plumber marks the bending point at 300 mm from the end, sets the hydraulic bender to 135°, and performs the bend. The resulting obtuse angle allows water to flow smoothly around the corner without significant pressure loss.
- Always wear appropriate PPE (gloves, safety boots, goggles)
- Inspect equipment before use
- Ensure the pipe is properly secured before bending
- Keep hands and loose clothing away from moving parts
- Work in a well-ventilated area
- Follow manufacturer instructions for the bending machine
- Wrinkling: Folds on the inner bend radius caused by excessive force
- Flattening: Reduction in pipe cross-section at the bend
- Cracking: Splitting on the outer bend radius due to over-bending
- Springback: Elastic recovery after bending (account for this by slight over-bending)
In Tanzanian homes and buildings, obtuse bends are commonly used when installing water supply pipes. For example, when running a water pipe from the main supply to a bathroom in a house in Dar es Salaam, a plumber may use a 135° obtuse bend to navigate around a wall corner. This allows the pipe to follow the wall contour smoothly while maintaining good water flow to taps and showers, avoiding sharp turns that could reduce water pressure or cause pipe damage over time.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings.
- Prepare sketches pattern
- Prepare template.
- Prepare work pieces.
- Construct obtuse bending
- Clean the work area and store tools in a safe place
- Store piecework.
Tathmini ya matokeo
Obtuse bend constructed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain:
- Constructing obtuse bend
Principles: The student should explain principles of:
- Constructing obtuse bend
Theories: The student should explain: -
- Different ways of performing obtuse bend
- Uses of obtuse bends
Detailed knowledge about:
- Safety precautions while constructing obtuse bend
- First aid
Swali
What is the angle range for an obtuse bend in pipe fitting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado