Mada za sehemu hiiInstalling taps and valvesMada 4
- Fixing screw down taps
- Fixing quick closing taps
- Fixing valve
- Fixing float valve
A float valve (also called a ball valve) is an automatic water control device that fills a storage tank or cistern to a set water level and stops the water flow when the tank is full.
A float valve is a plumbing fitting that controls the water level in tanks, cisterns, and reservoirs. It uses a floating ball connected to a lever mechanism. When the water level rises, the float lifts and gradually closes the valve; when the water level drops, the float falls and opens the valve to allow more water in.
- Ball Float Valve — Uses a hollow ball (usually made of plastic or copper) that floats on the water surface. This is the most common type in Tanzania.
- Cup Float Valve — Uses a cylindrical cup instead of a ball. It is less common but works on the same principle.
A typical ball float valve consists of these main parts:
- Float (ball) — Sits on the water surface and moves up and down with the water level
- Float arm — Connects the float to the valve body
- Valve body — Contains the valve seat and mechanism that controls water flow
- Inlet thread — The part that connects to the water supply pipe
- Washer and seat — The rubber seal that stops water flow when closed
- Adjusting screw — Allows fine-tuning of the water level setting
Float valves are used in:
- Toilet cisterns (flush tanks)
- Overhead water storage tanks in houses and schools
- Livestock water troughs
- Industrial water tanks
Step 1: Gather Tools and Materials
You will need:
- New float valve or repair kit
- Adjustable wrench or pliers
- Screwdriver
- Thread tape (Teflon tape)
- Pipe sealant
- Personal Protective Equipment (PPE) — gloves and safety goggles
Step 2: Turn Off Water Supply
Before starting any repair, shut off the water supply to the tank or cistern. This prevents water from overflowing while you work.
Step 3: Drain the Tank
Empty the storage tank or cistern so you can access the float valve easily. For toilet cisterns, flush to drain the water.
Step 4: Remove the Old Float Valve
- Use an adjustable wrench to loosen the nut connecting the valve to the supply pipe.
- Unscrew the valve from the tank or pipe fitting.
- Check the old valve to identify the problem — common issues include a worn washer, a cracked float, or a faulty valve seat.
Step 5: Install the New or Repaired Float Valve
- Clean the threaded connection on the pipe.
- Wrap thread tape clockwise around the inlet threads of the new valve (3 to 5 wraps).
- Apply a small amount of pipe sealant if needed.
- Screw the valve hand-tight, then tighten with an adjustable wrench. Do not overtighten, as this can crack the valve body.
Step 6: Attach the Float
- Connect the float arm to the valve body if it is separate.
- Ensure the float moves freely and does not touch the tank walls.
- Adjust the float arm length if necessary to set the correct water level.
Step 7: Test the Installation
- Turn on the water supply slowly.
- Watch the water level rise.
- The float should rise with the water and shut off the valve automatically when the tank is full.
- If the water overflows, adjust the float arm to lower the shut-off level.
- If the valve does not open enough, raise the float arm to increase water flow.
Step 8: Check for Leaks
Inspect all connections for leaks. Tighten any loose joints. If leaks persist, redo the thread tape and sealant.
| Problem | Possible Cause | Solution |
|---|---|---|
| Water keeps running | Worn washer or valve seat | Replace the washer or the whole valve |
| Float does not rise | Float is cracked or filled with water | Replace the float |
| Valve does not shut off | Float arm is too long | Shorten the float arm |
| Water overflows | Float level set too high | Adjust the float arm downward |
In Tanzania, many households and schools use overhead water tanks connected to rainwater harvesting systems or municipal supply. A common problem is a faulty float valve in the toilet cistern or tank, causing water to overflow and waste water — especially in areas where water is paid for by the bucket from vendors. If you live in a place like Mwanza or Arusha, fixing a leaking float valve yourself can save your family up to TZS 15,000 or more in water costs each month, and you can offer your neighbour a paid service to repair theirs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify proper tools for fixing float valves.
- Select the float/ball valve
- Install the ball valve to the proper location
- Identify the defects of the ball/float valve
- Service ball/float valve
- Clean tools and store them in a safe place.
Tathmini ya matokeo
Float valve fixed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of fixing float valve
Principles: The student should explain principles of:
- Fixing float valve
Theories: The student should explain: -
- Working principles of ball valves.
- Types of tools used to install and repair float valve
Detailed knowledge about:
- Safety precautions while fixing float valves
- Environment requirements
- First aid
Swali
What is the primary function of a float valve in a water storage tank?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado