Mada za sehemu hiiInstalling cold water supply to the buildingMada 2
- Installing and repairing direct cold-water supply systems
- Installing and repairing indirect cold water supply system
An indirect cold water supply system is a plumbing arrangement where water from the main public supply (municipal supply) first enters a storage tank installed at a high level (usually on the roof or a high platform) before being distributed to various fixtures inside the building. The water flows by gravity from the storage tank to the taps and appliances. This system is different from a direct system where water goes straight from the main supply to the fixtures without storage.
The indirect cold water supply system consists of several important components that work together:
-
Storage tank — A large container (usually made of plastic, fiberglass, or steel) that stores water collected from the main supply. It is installed at a high position to allow water to flow downward by gravity.
-
Ball valve — An automatic valve inside the storage tank that controls the water level. When the tank is full, the ball valve shuts off the water supply; when the water level drops, it opens to allow more water in.
-
Inlet pipe — The pipe that carries water from the main public supply into the storage tank.
-
Outlet pipe — The pipe that carries water from the storage tank to the various fixtures (basins, toilets, kitchens) inside the building.
-
Overflow pipe — A safety pipe that allows excess water to escape if the ball valve fails and the tank overfills.
-
Drain valve — A valve at the bottom of the tank used to empty the tank for cleaning or repairs.
-
Support structure — A sturdy platform or stand that holds the storage tank securely at the required height.
Before installing or repairing an indirect cold water supply system, gather the following tools and materials:
- Pipes (various sizes as required)
- Stock and die (for cutting and threading pipes)
- Pipe vice (holds pipes firmly during cutting/threading)
- Pipe wrench (tightens and loosens pipe fittings)
- Cold chisel (cuts pipes in tight spaces)
- Hacksaw (cuts metal or plastic pipes)
- Pipe cutter (clean cuts on pipes)
- Tape measure (measures pipe lengths)
- Spirit level (ensures pipes and tank are level)
- Ball valve (float valve for tank)
- Thread seal tape (seals pipe joints to prevent leaks)
- Storage tank (the main water container)
- Ball peen hammer (shapes and forms metal)
- Personal Protective Equipment (PPE): gloves, safety goggles, safety shoes
Step 1: Planning and Preparation
- Read the building plan or consult with the supervisor to determine where the storage tank will be placed.
- Ensure the location is high enough to provide adequate water pressure through gravity.
- Check that the support structure is strong enough to hold the full weight of the tank.
Step 2: Installing the Storage Tank
- Position the storage tank on the prepared support structure.
- Use a spirit level to ensure the tank is perfectly level. An unlevel tank may cause uneven water distribution and strain on the ball valve.
- Secure the tank firmly to prevent movement.
Step 3: Installing the Inlet Pipe
- Measure and cut the inlet pipe to the correct length using a hacksaw or pipe cutter.
- Thread the pipe ends using a stock and die set.
- Apply thread seal tape to the threaded ends to prevent leaks.
- Connect one end of the inlet pipe to the main water supply and the other end to the inlet fitting of the storage tank.
- Use a pipe wrench to tighten all connections securely.
Step 4: Installing the Ball Valve
- Insert the ball valve into the designated opening on the side or top of the storage tank.
- Ensure the valve is positioned correctly so the float arm can move freely.
- Tighten the valve using appropriate fittings and thread seal tape.
Step 5: Installing the Outlet Pipe
- Measure and cut the outlet pipe to run from the tank to the various fixtures.
- Connect the outlet pipe to the tank's outlet fitting.
- Route the pipe through the building to each required location, using brackets to support it.
Step 6: Installing the Overflow and Drain Pipes
- Attach the overflow pipe to the designated outlet near the top of the tank. This pipe should direct water away from the building foundation.
- Install the drain valve at the lowest point of the tank, connected to a drain pipe.
Step 7: Testing the System
- Turn on the main water supply and watch the tank fill.
- Check all joints and connections for leaks. If a leak is found, tighten the fitting or apply more thread seal tape.
- Ensure the ball valve automatically shuts off when the tank is full.
- Test water flow at all fixtures to confirm adequate pressure.
1. Leaking Joints
- Turn off the water supply.
- Identify the leaking joint and loosen it with a pipe wrench.
- Remove old thread seal tape and reapply fresh tape.
- Tighten the joint firmly and turn the water back on to check.
2. Faulty Ball Valve
- If water keeps overflowing, the ball valve may be damaged or the float may be improperly adjusted.
- Turn off the water supply and drain some water from the tank.
- Inspect the ball valve and float for cracks or damage.
- Replace the ball valve if necessary, ensuring the new valve is properly seated.
3. Blocked Pipes
- Use a pipe wrench to disconnect the blocked section.
- Clear the blockage using a pipe cleaner or by flushing with clean water.
- Reconnect the pipe and test the flow.
4. Tank Not Filling
- Check if the main water supply is turned on.
- Inspect the inlet pipe for blockages or kinks.
- Verify that the ball valve is functioning correctly.
- Always wear appropriate PPE including gloves, safety goggles, and safety shoes.
- Ensure the work area is clean and free of obstacles.
- Use tools correctly and only for their intended purpose.
- Be careful when working at heights; use a stable ladder or platform.
- Always turn off the water supply before starting any repair work.
In groups, inspect and repair the indirect cold water supply system in your school premises:
- Locate the storage tank and identify all components.
- Check for any visible leaks at joints and fittings.
- Test the ball valve to ensure it shuts off the water at the correct level.
- Inspect the overflow pipe to confirm it is clear and functioning.
- Make minor repairs such as tightening loose joints or replacing thread seal tape.
- Record your findings and any repairs made.
In Tanzania, many households in rural and peri-urban areas use indirect cold water supply systems with rooftop storage tanks to ensure reliable water access, especially when municipal water pressure is low or intermittent. For example, a family in Mwanza or Dodoma might install a 500-liter plastic storage tank on their roof to store water during night hours when the municipal supply is available, then use gravity-fed pipes to supply water to their kitchen, bathroom, and toilet during the day. This system reduces the need for expensive pump systems and ensures a steady water supply even during dry seasons when water scarcity is common.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Take measurements
- Select materials.
- Hacking the wall.
- Make a good disturbed area
- Perform joining pipes
- Perform pipe installation
- Clean the work area
- Clean tools
- Store tools
Tathmini ya matokeo
Indirect cold-water system installed and repaired as per the specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of installing indirect cold-water supply system.
Principles: The student should explain principles of installing indirect cold-water supply systems
Theories: The student should explain: -
- The merits and limitations of systems
- The advantages of using plastic pipes as compared to steel pipes
Detailed knowledge about:
- Safety precautions while installing indirect cold-water supply system
- Environment requirements
- Waste disposal
Swali
What is the main characteristic of an indirect cold water supply system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado