Mada za sehemu hiiPerforming thread cuttingMada 3
- Performing external thread cutting
- Performing internal thread cutting
- Performing imperial V-thread cutting
Internal thread cutting (also called tapping) is the process of cutting internal (female) threads inside a pre-drilled hole so that a bolt or screw can be fastened into it. This is commonly done using a lathe machine or a hand tap. Internal threads are found in engine blocks, cylinder heads, and many other vehicle components where bolts must be secured.
Before performing internal thread cutting, gather the following tools and equipment:
- Lathe machine with accessories or tapping wrench
- Centre drill
- Twist drills (different sizes)
- Thread plug gauge
- Thread pitch gauge
- Vernier calliper
- Micrometre
- Depth gauge
- Cutting fluid or lubricant
- Safety goggles and gloves
Step 1: Determine the Thread Size
Identify the required thread size from the workshop drawing or component specification. Common parameters include:
- Major diameter (outside diameter of the bolt that will fit)
- Thread pitch (distance between adjacent threads)
Step 2: Calculate and Drill the Pilot Hole
Calculate the correct drill size for the pilot hole using the formula:
Drill size = Major diameter − Pitch
For example, for an M10 × 1.5 mm thread:
- Major diameter = 10 mm
- Pitch = 1.5 mm
- Drill size = 10 − 1.5 = 8.5 mm
Drill the pilot hole to this calculated size using the appropriate twist drill on the lathe.
Step 3: Select the Correct Tap
Choose the right tap for the job. Taps come in three types:
- First tap (taper tap): Has a gradually tapered end; starts the thread easily
- Second tap (plug tap): Completes the thread after the first tap
- Bottoming tap: Used to cut threads close to the bottom of a blind hole
For through-holes, use the first tap followed by the second tap.
Step 4: Set Up the Workpiece on the Lathe
- Secure the workpiece firmly in the chuck or collet
- Ensure the workpiece is aligned with the lathe axis
- Set the correct cutting speed (slower speeds for larger diameters)
Step 5: Perform the Thread Cutting Operation
- Apply cutting fluid to the drill and the pilot hole
- Align the tap with the pilot hole using the tailstock centre or a tap wrench
- Start the lathe at low speed
- Apply steady downward pressure while turning the tap
- Turn the tap forward for one or two full turns, then reverse slightly to break the chip
- Repeat until the required thread depth is achieved
- Remove the tap carefully by reversing the rotation
Step 6: Check the Thread Quality
Use a thread plug gauge to verify the internal thread:
- The GO gauge should thread in smoothly
- The NO-GO gauge should not enter easily
If the thread is too tight, re-tap carefully. If it is too loose, the pilot hole may have been too large.
- Always wear safety goggles to protect eyes from flying chips
- Secure the workpiece firmly before starting the machine
- Use cutting fluid to reduce heat and wear
- Keep hands away from rotating parts
- Ensure the tap is properly aligned to avoid breaking it in the hole
A mechanic needs to cut an M8 × 1.25 mm internal thread in a vehicle engine component.
Solution:
-
Calculate the drill size:
- Major diameter = 8 mm
- Pitch = 1.25 mm
- Drill size = 8 − 1.25 = 6.75 mm (round to 6.8 mm)
-
Drill the pilot hole using a 6.8 mm twist drill.
-
Select taps: Use first tap (taper) then second tap (plug) for M8 × 1.25.
-
Cut the thread at low lathe speed with cutting oil, following the tapping procedure.
-
Check with thread plug gauge M8 × 1.25 to ensure proper fit.
In Tanzania, internal thread cutting is a vital skill for vehicle repair technicians at local garages and motor garages along major roads like the Dar es Salaam–Arusha highway. When a mechanic repairs a damaged cylinder head or fixes a stripped bolt hole in a customer's car, they use internal thread cutting to create new threads, restore the component, and ensure the vehicle runs safely. This skill helps small automotive workshops serve community members who depend on their vehicles for transport to markets, schools, and businesses.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret technical drawings
- Select tools and equipment
- Use lathe machines
- Observe safety precautions
- Clean tools, equipment, and workplace
- Store tools and equipment
Tathmini ya matokeo
Internal threaded workpiece conforms to technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Perform internal thread cutting on a lathe machine
Principles — the student should explain the principles of:
- Cutting internal threads
Theories — the student should explain:
- Procedure for cutting internal thread
Circumstantial knowledge — detailed knowledge about:
- Observing safety precautions while performing thread-cutting
- Safe handling of work tools, equipment and workpiece
Swali
Internal thread cutting is also known as what?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado