Mada za sehemu hiiPerforming arc weldingMada 4
- Performing hand arc welding bead
- Performing hand V joint
- Performing hand butt joint
- Performing hand tee joint welding
Performing Hand Arc Welding Bead
Arc welding is a metal-joining process that uses an electric arc to produce intense heat (about 6500°C at the electrode tip) that melts the base metal and a filler material called an electrode. When the molten metal cools and solidifies, it forms a strong bond between the pieces being joined.
Down hand arc welding (also called flat welding position) is the easiest type of welding where the workpiece is placed flat on a surface, and the weld is made without fighting gravity. This is the starting point for all beginning welders.
- Welding electrode: A metal rod with a chemical coating that melts during welding to fill the joint
- Weld joint: The way two pieces of metal are positioned for joining
- Welding machine: Equipment that provides electrical power to create the arc
- Ground clamp: A clamp that connects the workpiece to the welding machine to complete the electrical circuit
The welding circuit includes these main components:
- Power source – Provides AC or DC electricity
- Electrode holder – Holds the electrode and connects it to the machine
- Ground clamp – Attaches to the workpiece to complete the circuit
- Electrode – The filler material that melts to form the weld
- Control switches – Turn the machine on/off and adjust settings
Equipment:
- AC/DC arc welding machine
- Electrode holder and ground clamp
- Welding table or bench
Personal protective equipment:
- Welding shield/helmet
- Leather apron
- Welding gloves
- Safety boots
- Safety glasses
Hand tools:
- Chipping hammer (for removing slag)
- Wire brush (for cleaning)
- Tongs
- Clamps
Materials:
- Mild steel workpiece (e.g., 100 mm × 50 mm × 6 mm)
- Welding electrodes (e.g., E6013 or as specified)
Follow these steps carefully:
Step 1: Prepare Yourself and the Workpiece
- Wear all personal protective equipment (helmet, gloves, apron, boots)
- Clean the workpiece surface using a wire brush to remove rust, scale, and dirt
Step 2: Set Up the Machine
- Turn on the welding machine
- Adjust the current using the current adjuster. For a 6 mm thick plate, a current of 60–80 amperes is typically suitable
- Connect the ground clamp securely to one terminal of the machine
Step 3: Position the Workpiece
- Place the workpiece flat on the welding bench
- Clamp the workpiece firmly to prevent movement during welding
Step 4: Prepare the Electrode
- Attach the electrode to the electrode holder, ensuring it is tight and secure
- The electrode should be positioned to strike the arc at the starting point
Step 5: Strike the Arc and Weld
- Bring the electrode tip to touch the workpiece and quickly pull away slightly (maintain a 2–3 mm gap)
- Hold the electrode at an angle of 30° to 40° to the workpiece
- Move the electrode steadily along the joint in a straight line to create a uniform bead
- Maintain consistent speed and arc length throughout
Step 6: Clean the Weld
- Allow the weld to cool slightly
- Use the chipping hammer to remove the slag covering the weld bead
- Clean the welded joint thoroughly with a wire brush
Step 7: Finish
- Inspect your weld for smoothness and uniformity
- Turn off the welding machine
- Clean the work area and store tools properly
A student practices on a mild steel plate (100 mm × 50 mm × 6 mm):
| Parameter | Setting |
|---|---|
| Current | 70 A |
| Electrode | E6013, 3.2 mm diameter |
| Electrode angle | 35° |
| Travel speed | Steady, about 200 mm/min |
The student strikes the arc at one end of the plate and moves the electrode in a straight line to the other end, producing a smooth, uniform weld bead about 8–10 mm wide. After cooling, slag is chipped off to reveal the finished weld.
After completing the weld, examine it for:
- Smoothness – The bead should be regular without excessive spatter
- Penetration – The weld should have fused properly with the base metal
- Cracks – No visible cracks in the weld metal
- Uniformity – Consistent width and height along the entire length
Compare your weld with your classmates' work to identify differences in quality and discuss what might have caused any defects.
In Tanzania, arc welding is widely used in workshops for repairing vehicle bodies, fabricating metal parts, and constructing gates and door frames. For example, a mechanic at a local garage in Dar es Salaam would use down hand arc welding to attach a replacement patch panel on a damaged truck body, ensuring the vehicle is restored to safe and functional condition.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools, equipment, and materials
- Mark workpiece
- Cut workpiece
- Select welding current
- Weld workpiece
- Remove slag
- Observe safety precautions
- Clean tools, equipment, workpiece, and work place
- Store tools and equipment
Tathmini ya matokeo
Welded workpiece conforms to technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Prepare workpiece
- Weld different types of joints and sizes
Principles — the student should explain the principles of:
- Taking measurements
- Welding process
Theories — the student should explain:
- Types of welding
- Types of electrodes
- Properties of materials
- Application of AC and DC arc welding machines
Circumstantial knowledge — detailed knowledge about:
- Safety precautions while performing arc welding
- Safe handling of work tools, equipment and materials
- Waste disposal
Swali
What is the primary function of the welding electrode in arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado