Mada za sehemu hiiPerforming gas weldingMada 4
- Using gas welding tools and equipment
- Performing hand butt joint (gas welding)
- Performing hand lap joint (gas welding)
- Performing brazing
Performing Hand Lap Joint (Gas Welding)
A hand lap joint is a type of weld joint where one metal piece overlaps another and the edges are fused together using gas welding. In this joint, the metal pieces are placed so that one overlaps the edge of the other, creating a larger surface area for welding. The lap joint is commonly used when joining two metal sheets or plates of different thicknesses, providing a strong and reliable connection.
The term "hand" refers to the manual operation of the welding torch, where the welder controls the flame movement by hand rather than using automated equipment.
There are two main types of hand lap joints in gas welding:
1. Single Lap Joint
In a single lap joint, one metal piece overlaps the other along one edge only. One plate rests on top of the edge of the other plate, and the weld is applied along the overlapped edge on one side.
2. Double Lap Joint
In a double lap joint, both edges of one metal piece overlap the edges of the other piece. This creates a stronger joint because welds are applied on both sides of the overlap, providing more support and resistance to stress.
Before performing a hand lap joint, ensure the following tools and equipment are available:
- Oxy-acetylene welding equipment (oxygen and acetylene cylinders)
- Regulators for controlling gas pressure
- Gas hoses for connecting cylinders to the torch
- Welding torch with appropriate tips
- Filler rods (matching the metal being welded)
- Welding bench or work surface
- Clamps for holding workpieces in place
- Wire brush and files for cleaning metal
- Scribers, centre punch, steel rule, and try square for marking and alignment
- Personal protective equipment: welding goggles, leather apron, gloves, safety boots, and overall
Always observe the following safety measures before starting gas welding:
- Wear all personal protective equipment (PPE) including welding goggles, gloves, leather apron, safety boots, and overall.
- Ensure the welding area is clear of flammable materials.
- Check all gas connections for leaks before lighting the torch.
- Keep a fire extinguisher nearby.
- Work in a well-ventilated area.
- Never look directly at the welding flame without proper eye protection.
Step 1: Preparation of Workpieces
- Clean the metal surfaces to be joined using a wire brush to remove rust, dirt, and any contaminants.
- Mark the overlap area on the metal pieces using a scriber, steel rule, and try square.
- Ensure the overlap is uniform along the entire length of the joint.
Step 2: Fit-up and Clamping
- Position the two metal pieces so that one overlaps the other according to the required lap joint type.
- Use clamps to secure the workpieces firmly in place on the welding bench.
- Ensure proper alignment using a try square.
Step 3: Setting Up the Gas Welding Equipment
- Connect the oxygen and acetylene cylinders to their respective regulators.
- Check all hose connections for security.
- Open the cylinder valves slowly and adjust the regulators to the recommended working pressure.
- Connect the hoses to the welding torch.
Step 4: Lighting and Adjusting the Flame
- Use a striker to ignite the acetylene gas first.
- Slowly add oxygen to create a neutral welding flame (the flame should have a clear, sharp inner cone).
- The correct flame for welding steel has a bright white inner cone with a blue outer flame.
Step 5: Preheating the Joint
- Direct the flame onto the lap joint area to preheat the metal.
- Move the torch in a circular or sweeping motion to heat the entire overlap area evenly.
- The metal will change color as it heats, turning to a dull red when it is ready for welding.
Step 6: Applying the Weld
- Once the metal is preheated, begin adding the filler rod to the joint.
- Hold the torch at an angle of about 45 degrees to the workpiece surface.
- Move the torch along the joint in a slow, consistent motion while adding filler rod.
- The filler rod should melt and flow into the joint, forming a strong weld bead.
- For a single lap joint, weld along one side of the overlap.
- For a double lap joint, turn the workpiece and weld on the opposite side as well.
Step 7: Cooling and Cleaning
- Allow the welded joint to cool naturally without quenching.
- Clean the weld bead using a wire brush to remove any slag or spatter.
- Inspect the weld for uniformity and strength.
A student needs to join two mild steel plates, each 100 mm long, 50 mm wide, and 3 mm thick, using a single lap joint.
Procedure:
- Clean both plates with a wire brush.
- Place Plate A flat on the welding bench.
- Position Plate B so that it overlaps Plate A by 15 mm along one edge.
- Clamp both plates securely.
- Light the torch and adjust to a neutral flame.
- Preheat the overlapped area until it turns dull red.
- Add filler rod while moving the torch along the joint at a steady speed.
- Allow to cool and clean with a wire brush.
The result is a strong lap joint where the two plates are permanently fused along the overlapped edge.
In Tanzania, a mechanic at a local garage in Dar es Salaam or Arusha often uses hand lap joint welding to repair damaged motor vehicle body panels. When a car's door panel or fender has a hole or crack, the mechanic can overlap a patch piece over the damaged area and weld it using oxy-acetylene gas welding, restoring the panel's strength without replacing the entire part. This skill is valuable for small vehicle repair businesses as it saves costs on new parts and provides affordable repair services to customers.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools, equipment, and materials
- Mark workpiece
- Cut workpiece
- Light and adjust flame
- Weld workpiece
- Observe safety precautions
- Clean tools, equipment, workpiece, and work place
- Store tools and equipment
Tathmini ya matokeo
Welded workpiece conforms to technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Prepare workpiece
- Weld a lap joint using gas welding
Principles — the student should explain the principles of:
- Taking measurements
- Gas welding process
Theories — the student should explain:
- Types of lap joints
- Types of filler rods
- Properties of materials
- Application of oxy-acetylene welding
Circumstantial knowledge — detailed knowledge about:
- Safety precautions while performing gas welding
- Safe handling of gas welding equipment
- Waste disposal
Swali
What is a hand lap joint in gas welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado