Mada za sehemu hiiPerforming service of engine lubrication systemsMada 2
- Changing engine oil
- Changing engine oil filter
An oil filter is a component in an internal combustion engine's lubrication system. It is externally mounted on the side of the engine block. The oil filter traps and removes contaminants from engine oil before the oil circulates back through the engine to lubricate moving parts.
The primary purpose of oil filters is to remove contaminants from engine oil, ensuring that the oil remains clean and effective in lubricating engine parts. Without an oil filter, contaminated oil with worn-out particles would increase the wear and tear of the moving engine parts. This would directly increase the risk of reduced engine efficiency and damage.
Full-Flow Oil Filters
Modern engines are designed to use full-flow oil filters. A full-flow oil filter allows all oil to be filtered before entering the engine. If a motor vehicle has only one filter, it is most likely a full-flow filter design. The oil that goes through this filter lubricates the entire engine. It removes larger particles of contaminants from the oil that may be harmful to the engine.
Bypass Oil Filters
A bypass oil filter may be found in old motor vehicles. It only filters a proportion of the pump's oil output. The remainder of the oil is fed directly to the oil gallery. The filter media is very efficient because it is designed to remove the smallest particles of contaminants. The oil that passes through a bypass filter typically returns to the sump.
Tools, Equipment, and Materials Needed
- Set of screwdrivers
- Tool kit
- Drain pan
- Oil filter wrench
- Waste cotton
- Owner's manual book
- Lubricating oil
- New oil filter
- Safety glasses, gloves, overall, safety boots
Step-by-Step Procedure
- Ensure the motor vehicle is on a flat surface and the engine is switched off.
- Select tools and materials required.
- Insert wheel stoppers underneath the wheels of the vehicle.
- Open the motor vehicle bonnet.
- Ensure the engine is cool.
- Cover the working part of the motor vehicle body.
- Disconnect the negative battery terminal.
- Inspect for oil leakages in the engine.
- Clean the engine and oil filter with cotton waste.
- Identify the lubricant specifications used.
- Position the oil-draining pan beneath the oil filter.
- Loosen the oil filter and remove it from its mounting position.
- Inspect the oil filter and its thread.
- Lubricate the new oil filter face and positioning gasket.
- Fill the oil in the oil filter.
- Refit the new oil filter to the position where the old filter was.
- Remove the draining pan from underneath.
- Inspect the engine oil level and refill to the required level.
- Connect the battery terminal.
- Run the engine for a while and switch it off.
- Reinspect the engine oil level.
- Remove the cover positioned on the working vehicle body.
- Close the vehicle bonnet and remove the safety stand.
- Clean tools and working environment and store tools as per workshop regulations.
Important Safety Precautions
- Always ensure the engine is cool before starting work to avoid burns.
- Wear safety glasses and gloves to protect against oil splashes.
- Use wheel stoppers to prevent the vehicle from rolling.
- Disconnect the negative battery terminal to prevent electrical shorts.
During a practical lesson at a workshop in Dar es Salaam, Form 2 students at Mwalimu Nyerere Vocational Training Centre followed the procedure to change an oil filter on a training Toyota Corolla. After positioning the drain pan beneath the filter, student Mwinyimkuu used an oil filter wrench to carefully loosen the old filter. After inspecting the filter thread for damage, he lubricated the new filter gasket with clean engine oil, filled the filter with oil, and installed it by hand to avoid over-tightening. After reconnecting the battery and running the engine, the teacher helped him check the oil level and ensure there were no leaks.
In Tanzania, taxi and daladala drivers in cities like Arusha and Mwanza regularly change oil filters during routine vehicle servicing to keep their engines running efficiently and avoid costly repairs. A driver at Mwenge taxi rank might spend around TSh 15,000–25,000 for an oil filter change at a local garage, which is much cheaper than repairing an engine damaged by contaminated oil. This maintenance skill also helps small mechanic shops in rural areas generate income by offering oil filter replacement services to community members.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify oil filter location and type
- Remove old filter using correct tool
- Lubricate new filter gasket
- Install and hand-tighten the new filter
- Verify no leaks after start-up
- Observe safety precautions
Tathmini ya matokeo
Oil filter replaced per manufacturer's specifications.
Tathmini ya maarifa
Method used — the student should explain how to replace an oil filter.
Principles — the student should explain the principles of:
- Filtration
- Bypass valve operation
Theories — the student should explain:
- Oil filter types (spin-on, cartridge)
- Effects of dirty filter
- Filter service intervals
Circumstantial knowledge — detailed knowledge about:
- Hot oil safety
- Waste filter disposal
Swali
What is the primary function of an oil filter in a motor vehicle engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado