Mada za sehemu hiiServicing parking lightsMada 2
- Rectifying light combined switch and relays
- Replacing defective side lamps and bulbs
Rectifying Light Combination Switch and Relays
The parking light system of a vehicle relies on two important electrical components: the combination switch and the relay. When these components develop faults, the parking lights may fail to work properly. This note explains how to identify faults in these components and how to rectify them through systematic testing and repair procedures.
Parking lights, also called sidelights, are external lights installed at the front and rear corners of a vehicle. They serve an important safety purpose:
- Front parking lights are typically white or amber in colour
- Rear parking lights are usually red (red-white or amber)
The main functions of parking lights are:
- To make the vehicle visible when parked in dark or low-light areas
- To improve visibility in poor weather conditions such as fog
- To warn other road users of the parked vehicle's position
Important: Avoid leaving parking lights on for extended periods to prevent battery drainage. Some modern vehicles have automatic parking lights that turn off after a certain time.
The Combination Switch
The combination switch is a multi-function control located on the steering column. It controls:
- Headlights (high and low beams)
- Turn signals (left and right)
- Parking lights
This switch directs electricity to the appropriate circuit or relay. It has multiple terminals because it operates several different circuits within the lighting system.
The Relay
A relay is an electromagnetic switching device that uses a small current from the combination switch to control a larger current from the battery to operate the lights. Its functions are:
- To switch on the parking lights using a low-current signal
- To protect the combination switch from high currents that could damage it
Relay Pin Configuration
| Pin Number | Function |
|---|---|
| 85 | Ground (negative) for controlling circuit |
| 86 | Power from combination switch |
| 30 | Power from battery (main power input) |
| 87 | Output to lights (normally open) |
| 87a | Output to lights (normally closed) – only in 5-pin relays |
How it works: When pin 86 receives power from the combination switch, the electromagnetic coil activates and pulls the contact arm to connect pin 30 with pin 87, allowing current to flow to the parking lights.
Common Faults in Combination Switches
- One type of headlight beam does not illuminate
- Dashboard lights fail to illuminate
- Parking lights do not work
- Burned or corroded terminals
- Broken internal contacts
Procedure for Rectifying the Combination Switch
Step 1: Prepare the vehicle
- Select all required tools and safety gear
- Observe safety precautions
- Switch off the vehicle engine
- Disconnect the negative terminal of the battery
Step 2: Access the switch
- Remove the steering column cover
- Remove the combination switch from its position
Step 3: Inspect and test
- Perform visual inspection of ports, terminals, and sockets for damage or corrosion
- Check continuity between ports and pins using a multimeter
- Look for broken wires or loose connections
Step 4: Rectify or replace
- Clean corroded terminals with appropriate cleaning solution
- Repair open circuits using solder or by securing loose connections
- If the damage is too critical, replace the combination switch entirely
Step 5: Reassemble and test
- Install all removed components in reverse order
- Reconnect the battery negative terminal
- Test the performance of the combination switch
- Verify that parking lights illuminate correctly
Signs of Relay Failure
- Relay sticks in the closed position (lights stay on)
- Burned-out contacts (no current passes through)
- Clicking sound is not heard when activated
- Corrosion on relay pins
Procedure for Testing a Relay
Step 1: Prepare and inspect
- Select tools, equipment, and safety gear
- Observe all safety precautions
- Inspect the relay for physical damage, burnout, or corrosion
Step 2: Identify the controlling circuit pins
- Locate pins 85 and 86 (controlling circuit)
- If pins are not labeled, find the two small parallel pins among three parallel pins – these are pins 86 and 85
Step 3: Test the electromagnetic activation
- Connect pin 85 to the negative terminal of the battery
- Connect pin 86 to the positive terminal of the battery
- Listen for a clicking sound – this indicates the relay is activating
Step 4: Test continuity between output pins
- Using a multimeter, check resistance between pins 30 and 87
- A good relay should show nearly zero resistance (continuity) when activated
Step 5: Test with test lamp
- Supply battery voltage to pin 86
- Ground the test lamp and touch pin 87
- If the test lamp illuminates, the relay is functioning properly
Step 6: Complete testing
- Test the overall performance of the relay
- Clean and store all tools properly
| Fault | Possible Cause | Remedy |
|---|---|---|
| Parking lights do not illuminate | Blown fuse, defective switch, or bad relay | Check fuse, test switch and relay, replace as needed |
| One parking light not working | Burned out bulb or loose connection | Replace bulb or fix connection |
| Lights stay on continuously | Relay stuck in closed position | Replace the relay |
| Intermittent operation | Corroded terminals or loose wiring | Clean terminals, secure connections |
| Dashboard lights not working | Faulty combination switch | Test and replace combination switch |
- Always disconnect the battery negative terminal before working on electrical components
- Wear safety boots, gloves, and safety glasses
- Use insulated tools to prevent short circuits
- Work in a well-ventilated area
- Follow your teacher's instructions at all times
In Tanzania, understanding how to rectify combination switches and relays is valuable for motorcycle and car mechanics working in towns like Dar es Salaam, Arusha, or Mwanza. For example, a taxi driver operating a "daladala" or private car may experience parking light failures during rainy season due to water damage and corrosion. A trained mechanic can quickly test the relay using a multimeter (costing around TSh 50,000-80,000 at local hardware shops) and replace the faulty component, restoring the vehicle's safety features and ensuring the driver complies with traffic regulations requiring functioning parking lights at night.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear
- Interpret Park light circuits
- Diagnose system fault combined switch and relays
- Rectify fault combined switch and relays
- Test the combined switch and relays
- Observe safety
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Serviced combined switch and relays function according to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should describe how to service combined switch and relays
Principles: The student should explain the principles involved in servicing parking combined switch and relays
Theories: The student should explain:
- Application combined switch and relays
- Faults in combined switch and relays, causes and remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
Which relay pin receives power from the combination switch to activate the electromagnetic coil?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado