Mada za sehemu hiiAdjusting valve clearanceMada 2
- Performing valve overlap adjustment
- Performing one to one valve adjustment
Performing Valve Overlap Adjustment
Valve overlap adjustment is the process of setting the valves so that both the intake and exhaust valves are slightly open at the same time. This adjustment helps the engine perform better by allowing exhaust gases to leave smoothly and fresh air-fuel mixture to enter properly.
Valve overlap is the period during which both the intake valve and the exhaust valve are open at the same time. This happens at the end of the exhaust stroke and the beginning of the intake stroke in a four-stroke engine, as shown in Figure 2.16 in your textbook.
Why is Valve Overlap Important?
The main purposes of valve overlap are:
- Expelling exhaust gases: Helps old exhaust gases leave the cylinder more easily
- Allowing fresh mixture to enter: Creates room for fresh air and fuel to enter smoothly
- Increasing engine power: Improves overall engine performance
- Used in high-performance engines: Racing engines often use more overlap for higher power output
| Term | Meaning |
|---|---|
| Valve clearance | Small gap between the valve and the part that pushes it (rocker arm or camshaft) |
| Valve overlap | Period when both intake and exhaust valves are open simultaneously |
| TDC | Top Dead Centre - the highest position of the piston |
| Cylinder #1 | The first cylinder in the engine, usually at the front |
- Feeler gauge
- Torque wrench
- 10mm ring spanner
- Flat screwdriver
- Vehicle or stationary teaching model
- Service manual
Safety Equipment Required
- Overall
- Safety boots
- Gloves
- Safety clear glasses
Step 1: Preparation
- Select all tools and materials required
- Observe all safety precautions
- Obtain the lash specifications from the service manual
- Ensure the engine is at the desired temperature (usually cold for most engines)
- Disconnect the battery for safety
Step 2: Accessing the Valvetrain
- Remove the valve cover to access the camshaft and valvetrain
Step 3: Positioning the Engine
- Rotate the crankshaft to Top Dead Centre (TDC) of cylinder number 1 on the compression stroke
- Rotate the crankshaft slightly past TDC of the exhaust stroke for the specific cylinder being adjusted
Step 4: Measuring and Adjusting
- Use a feeler gauge to measure valve clearance
- If the clearance is incorrect, adjust using the adjusting screws:
- Loosen the locknut
- Turn the adjusting screw to set the correct clearance
- Tighten the locknut while holding the adjusting screw
Step 5: Completion
- Clean tools and working area
- Store tools as per workshop regulations
Suppose you are adjusting valve overlap on a petrol engine. The service manual specifies:
- Intake valve clearance: 0.25 mm
- Exhaust valve clearance: 0.30 mm
Procedure:
- Rotate engine to TDC of cylinder #1 (compression stroke)
- Rotate slightly past TDC on exhaust stroke
- Insert 0.25 mm feeler gauge for intake valve
- You should feel slight drag - not too tight, not too loose
- If too tight, loosen locknut and turn adjusting screw counterclockwise
- If too loose, turn clockwise
- Repeat for exhaust valve with 0.30 mm feeler gauge
- Tighten locknut to specification (e.g., 25 Nm using torque wrench)
| Valve Clearance | Valve Overlap |
|---|---|
| Gap between valve and rocker arm/camshaft | Time period when both valves are open |
| Set using feeler gauge | Adjusted by setting valve timing |
| Prevents valves from hitting pistons | Improves scavenging and performance |
| Too tight or too loose causes problems | Proper overlap increases power |
If valve overlap is not set correctly, you may experience:
- Engine misfire
- Tapping or ticking noise from valvetrain
- Hard starting or failure to start
- Excessive exhaust smoke
- Loss of engine power
- Burnt valves or overheating
From your textbook, make sure you can answer:
- Differentiate valve clearance from valve overlap
- What tool is commonly used to measure valve clearance?
- What are the possible effects of incorrect valve clearance on engine performance?
- Why is it important to adjust valve clearance when the engine is cold?
- Valve overlap occurs when both intake and exhaust valves are open simultaneously
- It improves engine performance by helping exhaust gases leave and fresh mixture enter
- Adjustment is done by rotating crankshaft to correct position and using feeler gauges
- Always follow service manual specifications for correct clearance values
- Safety precautions must be observed throughout the procedure
In Tanzania, a mechanic at a garage in Arusha or Dar es Salaam performing valve overlap adjustment can significantly improve a customer's vehicle performance. For example, after adjusting the valves on a Toyota saloon taxi (commonly used as a daladala), the engine runs smoother, consumes less fuel, and produces more power — saving the vehicle owner approximately TSh 50,000-100,000 in fuel costs over a month of city driving. This skill is also valuable for small garage owners who can offer valve adjustment services as part of their regular engine maintenance package.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear
- Use of service manual
- Locate the cylinder head and identify the valves to be adjusted
- Perform valve overlap adjustment
- Identify overlap position
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
Adjusted valve clearance conforms to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to perform valve adjustment:
- Valves overlap adjustment method
Principles: The student should explain the principles of the construction of the valve train mechanism
Theories: The student should explain:
- Effects of incorrect valve clearance on the engine
- Advantage of overhead camshaft engines compared to side cam shaft engines
- Reasons for some engines which need no valve clearance adjustment
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions Manufacture’s service manual
Swali
What is valve overlap in a four-stroke engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado