Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Performing counter boring drilled holes
Bench Drilling Machine Operations
A bench drilling machine is a versatile tool used in workshop settings to create holes in metal, wood, and other materials. It consists of a motor-driven spindle that holds drill bits, mounted on a sturdy bench or stand. In auto-electric mechanics, this machine is essential for creating holes when installing components, mounting brackets, and repairing vehicle parts.
Before operating the bench drilling machine, always observe these safety measures:
- Wear safety clear glasses to protect eyes from flying metal particles
- Wear gloves to protect hands from sharp edges and heat
- Wear safety boots to protect feet from dropped objects
- Wear overalls to protect clothing and skin
- Ensure the work area is clean and free of oil, grease, or debris
- Always secure the workpiece firmly in the vice
- Keep hands away from the rotating drill bit
- Ensure the drill bit is properly tightened before starting
- Disconnect power when changing drill bits or adjusting the machine
The following tools and materials are needed for drilling operations:
- Bench drilling machine with accessories
- Work bench
- Centre punch
- Hammer
- Set of drill bits (appropriate sizes)
- Oil can (for lubricating the drill bit)
- Wire brush (for cleaning the workpiece)
- Vernier caliper (for measuring hole diameter)
Marking the Hole Position
- Clean the workpiece surface using a wire brush to remove rust, dirt, or paint
- Use a vernier caliper to measure and mark the exact position where the hole will be drilled
- Mark the centre point with a pencil or scribe
Centre Punching
- Place the workpiece on the workbench or in a vice
- Position the centre punch at the marked point
- Strike the centre punch firmly with a hammer to create a small depression
- This depression guides the drill bit and prevents it from wandering
- Select the appropriate drill bit size for the required hole diameter
- Insert the drill bit into the chuck and tighten securely using the chuck key
- Adjust the drilling depth using the depth stop (if required)
- Ensure the workpiece is securely clamped to the worktable using a vice
- Apply a few drops of cutting oil to the marked position on the workpiece
Follow these steps to perform drilling:
- Start the machine: Switch on the drilling machine and allow the drill bit to reach full speed
- Position the workpiece: Ensure the centre-punched mark aligns with the tip of the drill bit
- Begin drilling: Lower the drill bit slowly onto the workpiece using the feed handle
- Apply cutting oil: Continuously apply cutting oil to cool the drill bit and workpiece
- Maintain steady pressure: Apply consistent, gentle pressure on the feed handle
- Complete the hole: Continue drilling until the desired depth is reached
- Withdraw the drill: Raise the drill bit slowly while the machine is still running
- Switch off: Turn off the machine and wait for the drill bit to stop completely
After completing the drilling operation:
- Clean the workpiece and remove any burrs using a file or deburring tool
- Clean the drill bit with a wire brush to remove metal filings
- Apply oil to the drill bit to prevent rust
- Store drill bits in a clean, dry place
- Clean the workbench and surrounding area
A student needs to drill a 10 mm diameter hole in a flat metal bar to mount an electrical component. The steps are:
- Measure the position using a vernier caliper — mark 50 mm from the edge
- Centre punch the marked position
- Select a 10 mm drill bit and insert it into the chuck
- Secure the metal bar in the vice
- Apply cutting oil to the marked point
- Start the machine and drill the hole to the required depth
- Switch off and remove the workpiece
- Clean the hole and check the diameter with the vernier caliper
In Tanzania, auto-electric mechanics in local workshops along Nelson Mandela Road or in towns like Arusha and Mwanza use bench drilling machines daily to create holes when installing batteries, mounting alternators, and repairing electrical harness brackets. For example, when a taxi driver needs a new radio installed, the mechanic may need to drill mounting holes in the dashboard, applying the same drilling skills learned in this topic.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools, equipment and materials
- Mark work piece
- Cut work piece to size
- Perform drilling
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools, equipment and work piece
Tathmini ya matokeo
Drilled hole conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Perform machine drilling process
Principles: The student should explain the principles of:
- Drilling
- Selection of drilling speed
Theories: The student should explain:
- drill size and drilling speed
- Drilling procedures
- Importance of coolant in drilling process
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Workshop rules and precautions
Swali
Which piece of personal protective equipment (PPE) protects the eyes from flying metal particles when using a bench drilling machine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado