Mada za sehemu hiiServicing power mirror systemsMada 2
- Diagnosing power mirror systems
- Rectifying power mirror system components
A power mirror system allows the driver to adjust the side mirrors using electrical controls rather than manually. Rectifying the power mirror system means finding and fixing faults so the mirrors work properly again. This involves checking each component, identifying problems, and repairing or replacing faulty parts.
Before rectifying, you must understand what each part does:
- Control switches – Let the driver choose which mirror to adjust and in which direction (up, down, left, right)
- Electric motors – Two small motors inside each mirror housing move the mirror glass horizontally and vertically
- Mirror glass – The reflective surface that can be tilted by the motors
- Wiring and connectors – Carry electrical power from the battery through switches to the motors
- Fuse and relay – Protect the circuit from overload; the relay acts as an electrical switch controlled by the control switch
Step 1: Safety First
Before working on any electrical system, observe safety precautions:
- Wear safety boots, gloves, safety glasses, and an overcoat
- Disconnect the vehicle battery negative terminal before starting electrical work
- Ensure the vehicle is parked on level ground with handbrake applied
Step 2: Identify the Complaint
Ask the driver or user what problem they observe. Common complaints include:
- One mirror not moving at all
- Mirror moving in only one direction (e.g., up but not down)
- Both mirrors failing to work
- Slow or jerky mirror movement
- Unusual noise from the mirror housing
Step 3: Visual Inspection
Examine the mirror system carefully:
- Check the mirror glass for cracks or damage
- Inspect the wiring harness for broken wires, loose connectors, or corroded terminals
- Look for signs of water entry into the mirror housing
- Check the fuse in the vehicle fuse box – a blown fuse often indicates a short circuit
Step 4: Test the Electrical Supply
Using a digital multimeter or test lamp:
- Set the multimeter to DC voltage (20V range)
- Connect the negative probe to a good earth (metal body)
- Turn the ignition to "ACC" or "ON"
- Probe the connector at the mirror motor while someone operates the switch
- The multimeter should show battery voltage (about 12V) when the switch is pressed
- If no voltage is present, the fault is in the supply circuit (switch, wiring, or relay)
- If voltage is present but the motor does not move, the motor is faulty
Step 5: Test Individual Components
Testing the control switch:
- Remove the switch from the door panel
- Use the continuity (continuity beep) function of the multimeter
- Check that each switch position creates a connection between the correct terminals
- No continuity when pressed means the switch is faulty and must be replaced
Testing the motor:
- Remove the motor from the mirror housing
- Connect it directly to a 12V battery (observe correct polarity)
- If the motor runs, it is good; if it does not run, replace the motor
- Listen for clicking or grinding sounds – these indicate internal damage
Step 6: Rectify the Fault
Based on your testing:
- Replace a blown fuse – but first check what caused it to blow (short circuit)
- Repair damaged wiring – solder or crimp new connections and use insulating tape
- Clean corroded connectors – use electrical contact cleaner and a wire brush
- Replace a faulty switch – install a new switch of the same type
- Replace a faulty motor – install a new motor and reassemble the mirror
Step 7: Final Test
After rectification:
- Reconnect the battery negative terminal
- Test all mirror movements (left, right, up, down) for both mirrors
- Check that the switch returns to centre (spring-loaded) when released
- Ensure no unusual noise or slow movement occurs
A driver reports that the left side power mirror on a Toyota Premio will not adjust upward, but all other directions work fine.
Diagnosis:
- Using the multimeter, voltage is present at the motor connector when the "up" button is pressed
- This means the switch and wiring are providing power correctly
- Connecting a 12V battery directly to the motor terminals shows no movement
- The motor is faulty (the upward direction motor inside the assembly is damaged)
Rectification:
- Replace the entire left mirror assembly (motors are not serviced separately in most vehicles)
- Reconnect the battery and test – the mirror now adjusts upward correctly
| Fault Symptom | Possible Cause | Solution |
|---|---|---|
| Both mirrors do not work | Blown fuse, relay faulty | Check/replace fuse, test/replace relay |
| One mirror does not move | Motor failure, broken wiring | Test motor, repair wiring |
| Mirror moves one direction only | Faulty switch, motor stuck | Test switch, replace if faulty |
| Slow movement | Weak motor, poor connection | Clean connectors, replace motor |
- In dusty conditions (many Tanzanian roads), regularly clean mirror adjusters to prevent grit from causing motor strain
- After seasonal rains, check for water entry into door panels that may cause corrosion
- Always carry spare fuses of the correct rating – cheap universal fuse sets are available at Mwenge Market in Dar es Salaam
In Tanzania, many taxis and daladalas (minibuses) use power mirrors for convenience. If a mirror stops working, a mechanic can quickly diagnose the fault using a multimeter and either repair the wiring or replace the faulty component. This skill is valuable at local vehicle repair garages in places like Arusha, Mwanza, or Dodoma, where keeping vehicles roadworthy directly supports the transport sector that connects people and goods across the country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Observe safety
- Select tools
- Replace power mirror system component
- Repair power mirror system component
- precautions
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Rectified power mirror system components operate as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Check power mirror system components
- Clear faults of power mirror system components
Principles: The student should explain the principles of:
- Operation of power mirror system components
- Rectifying power mirror system components
Theories: The student should explain:
- Function of power mirror components
- Faults in power mirror components causes and remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacturer’s services manual book
- Waste disposal
Swali
What is the first safety precaution a mechanic must take before working on the power mirror system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado