Mada za sehemu hiiDetermining characteristics of active electronic componentsMada 5
A transistor is a three-terminal semiconductor device that can regulate current or voltage and act as an electronic switch or amplifier. It is a fundamental building block in vehicle electronic systems.
A transistor is a semiconductor component formed by connecting two diodes back-to-back, creating two PN junctions. It has three terminals drawn from three semiconductor materials.
There are two main types of transistors:
- NPN Transistor: An N-type material is sandwiched between two P-type materials.
- PNP Transistor: A P-type material is sandwiched between two N-type materials.
Each terminal has a specific role:
-
Emitter (E): Heavily doped and relatively large. Its main function is to supply the majority of carriers (electrons in NPN, holes in PNP). It emits carriers toward the base.
-
Base (B): Thin and lightly doped. Its main function is to pass the majority of carriers from the emitter to the collector. It controls the current flow between emitter and collector.
-
Collector (C): Moderately doped and larger than the emitter. Its function is to collect the carriers that pass through the base from the emitter.
Purpose of Testing
Testing a transistor involves measuring its input and output characteristics to understand how it behaves in a circuit. The main characteristics tested are:
- Input characteristics: Relationship between base-emitter voltage (VBE) and base current (IB)
- Output characteristics: Relationship between collector-emitter voltage (VCE) and collector current (IC)
- Transfer characteristics: Relationship between IC and IB, which gives the current gain (β)
Required Tools and Equipment
- Transistor (BC 107 or equivalent)
- Multimeters (3 pieces)
- DC power supply
- Resistors: RB=100kΩ, RC=1kΩ
- Connecting wires
- Breadboard
- Safety gears (boots, gloves, overall)
Safety Precautions
- Wear safety boots, protective clothing, and gloves
- Ensure proper ventilation in the workshop
- Handle electronic components carefully to avoid static damage
Step 1: Identify Transistor Terminals
Before testing, identify the three terminals (E, B, C) and determine whether the transistor is NPN or PNP. This information can be found in the transistor's datasheet.
Step 2: Set Up the Common Emitter Circuit
Connect the transistor in a Common Emitter (CE) configuration as shown in Figure 1.7 of the textbook:
- Connect RB (100kΩ) between the base and the base supply voltage (VBB)
- Connect RC (1kΩ) between the collector and the collector supply voltage (VCC)
Step 3: Test Input Characteristics
- Fix the collector voltage (VCB) by adjusting VCC to minimum
- Vary the base-emitter voltage (VBE) in steps of 0.05V by adjusting VBB
- Measure VBE using a multimeter
- To determine base current (IB), measure the voltage across RB (VRB) and use the formula: IB=RBVRB
- Record readings in the input characteristics table
- Repeat for another value of VCB (for example, 2V)
Step 4: Test Output Characteristics
- Set IB=0 by setting VRB=0 (short the base resistor)
- Vary the collector voltage (VCE) in steps of 1V by adjusting VCC
- Measure the corresponding collector current (IC) using a multimeter
- Record readings in the output characteristics table
- Repeat for at least five different values of IB by adjusting VBB
Step 5: Plot Characteristics and Calculate Parameters
- Input characteristics graph: Plot VBE (x-axis) against IB (y-axis)
- Output characteristics graph: Plot VCE (x-axis) against IC (y-axis) for different IB values
- Transfer characteristics graph: Plot IB (x-axis) against IC (y-axis) at a fixed VCE
The slope of the transfer characteristics gives the current gain (βac): βac=ΔIBΔIC
A transistor is tested in a Common Emitter circuit with RB=100kΩ. The voltage measured across RB is 2V.
Calculate the base current (IB)
Solution: IB=RBVRB=100,000Ω2V=0.00002A=20μA
If the collector current measured is 2mA at a base current of 20μA, calculate the current gain (β):
Solution: β=IBIC=20μA2mA=0.00002A0.002A=100
A good transistor should show:
- Proper conduction when forward-biased between base and emitter
- No conduction (or very tiny leakage) when reverse-biased
- Current gain (β) within the expected range (typically 50-200 for BC107)
- Consistent readings across multiple measurements
A defective transistor may show:
- Short circuit between any two terminals
- Open circuit (no continuity)
- Very low or very high current gain outside normal range
In Tanzanian vehicle repair shops, transistors are tested when diagnosing faulty electronic control systems. For example, when a motorcycle's indicator lights fail to flash properly, a mechanic tests the transistor in the flasher relay unit to determine if replacement is needed. Modern vehicles in Tanzania rely heavily on transistors in ECUs (Engine Control Units), ignition coils, and voltage regulators, making this skill essential for auto-electricians working on cars like Toyota, Nissan, and locally used minibuses (daladala).
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select relevant safety gears, tools and equipment
- identify transistor terminals
- Test transistor
- Read and interpret transistor readings as per data book
- Observe safety regulations
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
A tested transistor conforms to specifications as per electronic component data books
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test a transistor
Principles: The student should explain the principals involved in testing characteristics of a transistor
Theories: The student should explain:
- Types of transistor
- Function of transistor
- Characteristics of transistor
- Transistor symbols
Circumstantial knowledge:
Detailed knowledge about:
- Electronic component data books
Swali
Which of the following correctly describes a transistor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado