Mada za sehemu hiiConstructing simple electronic circuitsMada 5
- Constructing inductive circuit
- Constructing capacitive circuit
- Constructing resistive circuits
- Constructing (RLC) circuit
- Constructing rectifier circuits
Constructing Resistive Circuits
A resistive circuit is an electronic circuit made up of resistors connected together to control current flow and voltage distribution. Resistors are passive electronic components that resist the flow of electric current, converting electrical energy into heat. They are essential in vehicle electronic systems for controlling current, dividing voltages, and protecting sensitive components.
In auto-electric systems, resistive circuits are used in instrument clusters, lighting control, sensor circuits, and voltage divider networks. Understanding how to construct series and parallel resistive circuits is fundamental to diagnosing and repairing vehicle electrical problems.
Series Connection
In a series connection, resistors are connected end-to-end, forming a single path for current flow. The same current flows through each resistor, but the voltage is divided among them.
Key characteristics of series circuits:
- Current is the same at all points (Itotal=I1=I2=I3)
- Total resistance equals the sum of individual resistances (Rtotal=R1+R2+R3)
- Total voltage equals the sum of individual voltage drops (Vtotal=V1+V2+V3)
- If one resistor fails (opens), the entire circuit stops working
Parallel Connection
In a parallel connection, both ends of each resistor are connected to the same two points, creating multiple paths for current flow.
Key characteristics of parallel circuits:
- Voltage is the same across all branches (Vtotal=V1=V2=V3)
- Total current divides among the branches (Itotal=I1+I2+I3)
- Total resistance is found using the reciprocal formula: Rtotal1=R11+R21+R31
- For two resistors in parallel: Rtotal=R1+R2R1×R2
- If one resistor fails, current can still flow through other branches
Follow these steps under teacher supervision:
- Select tools and safety gear — Put on safety boots, overalls, gloves, and safety goggles before starting.
- Plan your circuit — Determine the required total resistance and calculate individual resistor values using the series formula.
- Identify resistor values — Read the colour bands on each resistor to confirm their resistance values. The colour code uses bands: first two bands give digits, third band gives multiplier, fourth band gives tolerance.
- Arrange the resistors — Connect the resistors in series on the electronics board or breadboard by placing them end-to-end.
- Connect to power supply — Attach the circuit to the DC power supply, ensuring correct polarity.
- Measure voltage — Use a multimeter set to voltage (V) to measure voltage across each resistor and record your readings.
- Measure current — Connect the multimeter in series (set to current/mA) to measure circuit current.
- Verify calculations — Compare measured values with calculated expected values.
- Clean and store — Disconnect power, disassemble the circuit, and return tools to their storage locations.
- Select tools and safety gear — Wear all required safety equipment.
- Plan your circuit — Calculate the expected total resistance for your chosen resistor values.
- Arrange the resistors — Connect both ends of each resistor to the same two points (bus bars) on the breadboard.
- Connect to power supply — Attach the circuit to the DC power supply terminals.
- Measure voltage — Verify that voltage is the same across each parallel branch.
- Measure branch currents — Use the multimeter to measure current through each branch.
- Calculate total current — Add all branch currents and verify they equal the total current from the power supply.
- Verify resistance — Use the multimeter's resistance (Ω) function to measure total resistance and compare with calculations.
- Clean and store — Properly return all equipment.
A vehicle instrument panel circuit uses three resistors connected in series: R1=100Ω, R2=200Ω, and R3=300Ω. The circuit is connected to a 12V battery (common in vehicles).
Calculate:
(a) Total resistance (b) Current flowing through the circuit (c) Voltage drop across each resistor
Solution:
(a) Total resistance: Rtotal=R1+R2+R3=100+200+300=600Ω
(b) Current (using Ohm's Law: I=RV): I=600Ω12V=0.02A=20mA
(c) Voltage drop across each resistor:
- V1=I×R1=0.02A×100Ω=2V
- V2=I×R2=0.02A×200Ω=4V
- V3=I×R3=0.02A×300Ω=6V
Verification: Vtotal=V1+V2+V3=2+4+6=12V ✓
Two resistors, R1=4Ω and R2=4Ω, are connected in parallel across a 12V vehicle battery.
Calculate:
(a) Total resistance (b) Total current drawn from the battery
Solution:
(a) For two resistors in parallel: Rtotal=R1+R2R1×R2=4+44×4=816=2Ω
(b) Total current: Itotal=RtotalV=2Ω12V=6A
This shows that parallel resistance is always less than the smallest individual resistor — allowing more current to flow than a single resistor would permit.
- Always disconnect power before making or modifying circuit connections
- Never exceed component voltage or current ratings
- Use appropriate measurement ranges on the multimeter
- Report any damaged components to your teacher immediately
- Keep the work area clean and free of metal objects that could cause short circuits
In Tanzania, auto-electricians use resistive circuit knowledge daily when diagnosing vehicle electrical problems. For example, when a dashboard fuel gauge or temperature sensor stops working, a mechanic in Dar es Salaam or Mwanza uses a multimeter to measure voltage drops across resistors in the sensor circuit. By understanding series and parallel resistance values, they can identify whether a resistor has failed and replace the correct component, restoring the gauge to working condition without replacing expensive entire instrument clusters.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select relevant safety gears, tools, equipment and material
- Interpret the resistive circuit diagram
- Construct
- Observe safety regulations
- Clean tools, work place
- Store tools, materials
Tathmini ya matokeo
Constructed resistive circuits function as per technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to connect resistors in series and parallel circuit
Principles: The the principles involved in Constructing resistive circuit
Theories: The student should explain:
- Application of resistive circuits
- Characteristics of series resistive parallel resistive
Circumstantial knowledge: about:
- Safety precautions
- electronic component data sheets
Swali
In a series resistive circuit with three resistors (R1 = 100Ω, R2 = 200Ω, R3 = 300Ω) connected to a 12V battery, what is the total resistance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado