Mada za sehemu hiiServicing transmission systemsMada 3
- Checking clutch free play
- Servicing gear box
- Servicing propeller shaft
A manual gearbox (also called a transmission gearbox) is a system inside a vehicle that transfers power from the engine to the wheels. The driver selects different gears using a gear lever to control the vehicle's speed and torque.
The manual gearbox performs several important functions:
- Reduces speed and increases torque – It allows the engine's high speed to be reduced while producing more pulling power for the wheels.
- Changes direction of motion – It enables the vehicle to move forward or in reverse.
- Provides neutral position – It allows the engine to run while the vehicle is stationary (idle) without moving.
- Matches power to driving conditions – Lower gears give more power for climbing hills or carrying heavy loads, while higher gears give more speed on flat roads.
Regular gearbox servicing keeps the transmission system working properly and extends the life of the vehicle. Without proper servicing:
- Gear oil becomes dirty and loses its lubricating ability
- Internal metal parts wear out faster
- Gear shifting becomes difficult or noisy
- The gearbox may eventually fail, requiring expensive repairs
Follow these steps carefully when servicing a manual gearbox:
Step 1: Prepare Tools and Materials
Gather all required items before starting:
- Cotton rags
- Gearbox oil (correct grade as specified in service manual)
- Tool kit
- Safety gears (overall, gloves, safety boots, safety clear glasses)
- Service manual
- Service bed or oil draining pan
- Screwdrivers
- Drain plug spanner (SST)
Step 2: Observe Safety Precautions
- Wear safety boots, overalls, gloves, and safety glasses at all times
- Make sure the vehicle is on a level surface
- Allow the engine to cool before draining hot oil
Step 3: Secure the Vehicle
Insert wheel stoppers on all wheels to prevent the vehicle from rolling.
Step 4: Check for Oil Leakages
Set the service bed underneath near the gearbox. Inspect the gearbox housing and surrounding areas for any signs of oil leaks.
Step 5: Check the Oil Level
Unplug the gearbox top plug (filler plug). Use your finger or a dipstick to check if the oil reaches the bottom of the filler hole. If the oil is below the hole, the level is low and needs topping up.
Step 6: Drain the Old Oil
Set the oil draining pan underneath the gearbox. Use the drain plug spanner to loosen and remove the oil draining plug. Allow all the old oil to drain completely into the pan.
Step 7: Reinstall the Drain Plug
Once the oil has drained, clean the drain plug and its sealing washer. Tighten the oil-draining plug securely to its position using the spanner.
Step 8: Refill with Fresh Gearbox Oil
Refer to the service manual for the correct type and quantity of gearbox oil. Using a pump, refill fresh gearbox oil into the transmission through the top filler hole until the oil reaches the bottom of the hole.
Step 9: Verify Oil Level and Close
Check that the oil level is correct (flush with the bottom of the filler hole). Then tighten the top plug securely to its position.
Step 10: Clean Up
Remove the servicing bed and wheel stoppers from underneath the wheels.
Step 11: Store Tools and Clean Area
Wipe all tools clean and store them properly according to workshop regulations. Clean the working area and dispose of old oil safely.
Suppose you are servicing a Toyota Hilux at your school workshop. The service manual specifies using SAE 80W-90 gear oil. After draining the old oil and reinstalling the drain plug, you pump fresh oil into the gearbox. You continue adding oil until it just begins to overflow from the filler hole. This shows the oil level is correct—flush with the bottom of the filler hole. You then tighten the top plug and wipe away any spilled oil.
- Always refer to the service manual for the correct oil grade and quantity for each vehicle
- Never overfill the gearbox with oil—this can cause leaks and damage seals
- Change the oil while the engine is warm (not hot) for better drainage
- Always use a pump when refilling gearbox oil to avoid spillage
In Tanzania, many small businesses rely on vehicles for transport and delivery—such as dalali (local taxi) drivers or owners of small delivery trucks in towns like Arusha or Mwanza. Regularly servicing the gearbox of these vehicles prevents breakdowns and expensive repairs. For example, a dalali driver who changes the gearbox oil every 10,000 km can avoid a major transmission failure that might cost over TSh 500,000 to repair, keeping the vehicle running smoothly for daily income generation.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use the service manual
- Select tools and equipment
- Diagnose gear box components
- Repair the fault components
- Perform lubrication of gearbox parts
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools, equipment and parts
Tathmini ya matokeo
Serviced gear box conforms to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Inspect the gear box
- Service the gear box
Principles: The student should explain the principles involved in servicing gear boxes
Theories: The student should explain:
- Functions of gearbox
- Types of gearboxes
- Importance of servicing gearbox
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacturer’s service manual book
Swali
What is the primary function of a manual gearbox in a vehicle?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado