Mada za sehemu hiiCarrying out arc welding on non-ferrous metalsMada 2
- Performing arc welding on aluminium material parts
- Performing arc welding on copper material parts
Arc welding on aluminium is a specialised skill used to repair vehicle body parts made of aluminium alloys. Unlike steel, aluminium requires specific techniques because it melts at a lower temperature, conducts heat quickly, and forms an oxide layer that must be removed before welding.
Aluminium has several properties that affect how it is welded:
-
Low melting point – Pure aluminium melts at about 660°C, while aluminium alloys melt between 475°C and 635°C. This means the weld cools quickly and can crack if not handled properly.
-
High thermal conductivity – Aluminium conducts heat away from the weld area fast, requiring higher heat input or preheating before welding thick sections.
-
Oxide layer – Aluminium naturally forms a hard oxide layer (aluminium oxide) on its surface that melts at over 2000°C. This layer must be removed before welding, or the weld will be weak and porous.
-
Low density – Aluminium is light, which is why it is used in vehicle body parts to reduce weight, but it also means it warps easily when heated unevenly.
Proper preparation is the most important step in aluminium welding. Follow these steps:
-
Clean the work area – Remove any paint, grease, oil, or dirt from the aluminium surface using a degreaser or clean cloth.
-
Remove the oxide layer – Use a stainless steel wire brush or aluminium-specific brush to scrub the surface thoroughly. This must be done immediately before welding because aluminium forms a new oxide layer within minutes.
-
Fit the parts together – Ensure the metal pieces fit tightly with minimal gaps. Use clamps or a bench vice to hold them in position.
-
Preheat thick sections – For aluminium thicker than 6mm, use a torch to warm the metal slightly (about 50°C to 80°C) to reduce cracking.
For aluminium welding, TIG (Tungsten Inert Gas) or MIG (Metal Inert Gas) welding machines are preferred because they use inert gas that protects the weld from contamination.
Equipment Setup Steps
-
Select the correct wire – Use an aluminium welding wire that matches the parent metal (commonly ER4043 or ER5356).
-
Set the machine – Adjust the current and voltage according to the thickness of the aluminium. Thicker material requires higher current.
-
Connect the gas supply – Attach the argon gas cylinder and set the flow rate to about 15–20 litres per minute for TIG welding.
-
Prepare the electrode – For TIG welding, use a tungsten electrode sharpened to a point. For MIG, thread the aluminium wire through the feed rollers correctly.
-
Connect earth clamp – Attach the earth clamp firmly to the aluminium workpiece, making sure the contact is clean.
Practical Example
A student is welding a small aluminium panel on a vehicle door. The panel is 2mm thick and has a 1mm gap to fill.
-
Strike the arc – Start the arc using the TIG torch, maintaining a short arc length.
-
Form the pool – Allow a small weld pool to form, watching the molten metal flow.
-
Add the filler wire – Feed the aluminium wire into the front edge of the pool at a steady rate. The wire should melt and fuse with the base metal.
-
Move the torch – Travel slowly and steadily along the joint, keeping the weld pool uniform. Move in a straight line or slight weave pattern.
-
Complete the weld – Continue until the joint is fully filled. Let the weld cool naturally – do not quench with water.
- Always wear the welding shield with the correct shade lens (usually shade 10–12 for TIG/MIG).
- Wear leather gloves and protective clothing to prevent burns from sparks and hot metal.
- Ensure good ventilation or use a fume extractor, as aluminium welding produces harmful fumes.
- Keep a fire extinguisher nearby and clear the work area of flammable materials.
- Use tongs to handle hot aluminium pieces.
- Check all cables and connections for damage before starting.
| Defect | Cause | Prevention |
|---|---|---|
| Porosity (holes in weld) | Contaminated surface, incorrect gas flow, or too fast travel speed | Clean thoroughly, ensure proper gas coverage, reduce travel speed |
| Cracking | Rapid cooling, wrong filler wire, or high stress on joint | Use correct filler, preheat thick sections, allow slow cooling |
| Lack of fusion | Low heat input or incorrect angle | Increase current, keep torch at proper angle (about 70–80°) |
| Burn-through | Too much heat or too slow travel for thin material | Reduce current, increase travel speed |
After welding, inspect the joint for:
- Uniform bead appearance without gaps or excessive spatter
- No cracks visible on the weld surface
- Good penetration into the base metal
- The weld colour should be bright silver – dark or black colour indicates oxidation or contamination
Use a chipping hammer and wire brush to clean the weld and reveal any hidden defects.
In Tanzania, arc welding on aluminium is used in vehicle repair shops across the country, from Dar es Salaam to Mwanza and Arusha. When a taxi or daladala (minibus) gets into an accident and the aluminium bumper or door panel is damaged, a trained panel beater uses TIG or MIG welding to restore the vehicle. This skill enables a technician to run a profitable mobile welding business, repairing aluminium parts for cars, trucks, and tractors, thereby earning an income in Tanzanian shillings while providing an essential service to the community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Inspect the machine, cable and welding holder
- Interpret working drawing
- Prepare materials for welding
- Select types and sizes of consumable wires
- Align and tack the workpiece
- Maintain Angle and arc length
- Control travel speed along the joint
- Clean workplace, tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
Welded thick aluminium plate conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain
- Resistance welding technique used
- Welding procedure
Principles: The student should explain the principles of:
- Welding thick materials
- Heat treatment
- Purging
Theories: The student should:
- Describe properties of non-ferrous materials
- State metallurgy of materials
- Explain heat treatment processes
- Outline welding polarities and application
- Describe weld defects
- Interpret technical drawing skills
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while welding thick plates
- First Aid
Swali
Before arc welding aluminium, the oxide layer must be removed because:
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado