Mada za sehemu hiiCarrying out fabrication of motor-vehicle wing panelMada 5
Making Wing Panels
Wing panels are curved metal sections that form the outer bodywork of a vehicle, particularly above the wheel arches. Making wing panels is a fundamental skill in auto-body repair that involves measuring, cutting, forming, and joining sheet metal to create or repair vehicle body components.
Wing panels can be classified into:
- Front wing panels – located above the front wheel arches
- Rear wing panels – located above the rear wheel arches
- Wheel arch panels – curved sections that surround the wheels
Before starting any wing panel fabrication, ensure you have:
- Working drawings and measurements
- Measuring tape and try square
- Scriber for marking
- Hammer and anvil for shaping
- Bending machine
- Cutting machine (shear or saw)
- Seaming machine for joining edges
- Forming tools (mallets, dollies)
- Grooving tools for creating seams
Always wear:
- Clear goggles
- Leather apron and gloves
- Industrial boots
- Canvas spats
- Overalls
Step 1: Reading and Interpreting Working Drawings
Study the working drawing to understand:
- The dimensions of the wing panel
- The curvature and contour required
- The position of mounting points
- The type of material to be used (usually mild steel or aluminum)
Step 2: Taking Measurements
Use a measuring tape and try square to:
- Measure the area where the panel will be fitted
- Transfer dimensions from the working drawing to the metal sheet
- Mark all reference points clearly with a scriber
Step 3: Cutting the Metal Sheet
Using the cutting machine:
- Cut the metal to the approximate size, leaving extra material for trimming
- Ensure straight cuts using the try square as a guide
- Deburr edges to remove sharp pieces
Step 4: Forming the Curve
Use the bending machine and forming tools:
- Bend the metal gradually to match the required curvature
- Work from the center outward to maintain symmetry
- Use the hammer and anvil to fine-tune curves
- Check against the working drawing frequently
Step 5: Creating Seams
Use grooving tools and seaming machine:
- Create appropriate seams along the edges
- Ensure seams are tight and weather-resistant
- The seam type depends on the vehicle design
Step 6: Fitting and Trimming
- Test fit the panel on the vehicle body
- Trim any excess material
- Make final adjustments for proper alignment
A vehicle has a front wing damaged in an accident. The working drawing shows the wing panel dimensions as 450 mm width × 300 mm height, with a curvature radius of 180 mm.
Procedure:
- Measure the existing undamaged wing on the opposite side of the vehicle for reference
- Transfer dimensions: 450 mm × 300 mm to the metal sheet
- Cut the metal leaving 15 mm excess on all sides
- Set the bending machine to create 180 mm radius curve
- Form the curve gradually, checking fit every few bends
- Create a 10 mm flange seam along the mounting edge
- Trim to final dimensions and test fit
After fabrication, verify:
- Dimensions match the working drawing
- Curves are smooth and even
- Seams are properly closed
- Panel aligns correctly with adjacent body parts
- No cracks or damage to the metal
| Defect | Cause | Prevention |
|---|---|---|
| Uneven curves | Rushing the bending process | Work gradually, check frequently |
| Cracks | Over-bending or working cold metal | Use proper annealing techniques |
| Poor fit | Incorrect measurements | Double-check all measurements |
- Always wear PPE before starting work
- Secure metal sheets properly before cutting
- Keep fingers away from cutting blades
- Lift heavy panels with help
- Clean up metal scraps to prevent injuries
In Tanzania, auto-body repair skills are valuable in towns like Arusha, Mwanza, and Dodoma where many vehicles travel on rough roads and often sustain wing panel damage from potholes or accidents. A student trained in making wing panels can start a small repair business or work at local garages, charging around TSh 50,000 to 150,000 for repairing a damaged front wing panel — skills that directly support both employment and keeping vehicles safely on Tanzanian roads.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Interpret working drawings
- Take correct measurement
- Calculate allowances using formulae
- Develop different types of patterns
- Operate different types of sheet metal works equipment
- Assemble the developed patterns to form the required item as per drawing
- Observe safety regulation rules
- Clean work place
- Clean and store tools and equipment
Tathmini ya matokeo
Wing panel fabricated as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to wing panels
Principles: The student should explain the principles of:
- Developing different types of patterns
- Transforming drawing measurement to a sheet metal
- Obtaining forming allowances
Theories: The student should :
- Describe the properties of materials
- Explain transformation of measurements from drawing to a sheet metal
- Explain the construction of geometrical figures
- Outline the development techniques of cylinder, cylinder with oblique top and cones
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing sheet metal works
Swali
Which of the following is a type of vehicle wing panel?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado