Mada za sehemu hiiPerforming hand shearing/snippingMada 3
- Performing straight shearing
- Performing combination hand shearing/snipping
- Performing circular
Performing Circular (Curve) Hand Shearing
Circular or curve shearing is the process of cutting curved lines and circles in sheet metal using hand tools such as tin snips. This technique is essential in auto-body repair for forming curved panels and shapes.
Circular shearing (also called curve shearing) is a hand cutting method used to cut curved lines, circles, and irregular shapes in thin sheet metal. Unlike straight shearing, this process requires the cutter to turn the metal or the tool as they cut along a marked line.
Circular Tin Snips
- Designed for cutting external curves and circles
- The blades curve outward to allow smooth turning while cutting
- Used when cutting clockwise or counter-clockwise curves
Curve Tin Snip
- Also called a bent snip or offset snip
- Has blades bent to access difficult areas
- Useful for cutting inside curves and complex shapes
Step 1: Interpret the Working Drawing
Study the drawing to understand the required curve or circular shape. Note the dimensions and radius of any curves.
Step 2: Select Tools and Equipment
Choose the appropriate tin snips based on the type of curve:
- Circular tin snips for external curves
- Curve tin snips for internal curves
Step 3: Mark Out the Work
- Use a scriber and ruler to mark the curve or circle on the metal sheet
- For circles, use a centre punch to mark the center
- Use a compass or trammel points to draw the required radius
- Mark the cutting line clearly
Step 4: Prepare the Workpiece
- Secure the metal sheet on the work bench using a bench vice if needed
- Ensure the sheet is held firmly but not distorted
Step 5: Perform the Cutting
- Start cutting from the edge of the marked line
- For external curves: use circular tin snips, turning the snips as you follow the line
- For internal curves: use curve tin snips
- Cut slowly and steadily, following the marked line precisely
- Allow the snip blades to do the work — do not force them
Step 6: Finish the Cut
- Check the cut piece matches the required dimensions
- Use files to remove any burrs or sharp edges
- Smooth the edges with a file for safety
- Always wear hand gloves when handling sheet metal
- Wear safety glasses to protect eyes from metal fragments
- Wear overalls for body protection
- Remove sharp burrs and edges immediately after cutting
- Keep fingers away from the cutting path of the snips
A student needs to cut a circular disk of 150 mm diameter from a galvanized metal sheet.
Solution:
-
Mark the center: Use a centre punch to mark the center point on the metal sheet.
-
Draw the circle: Using a ruler and compass, draw a circle with radius 75 mm (half of 150 mm) around the center point.
-
Select the tool: Use circular tin snips for cutting the external curve of the circle.
-
Start cutting: Begin at the edge of the circle and turn the snips as you cut around the marked line.
-
Finish and check: After cutting, verify the diameter is 150 mm and file any rough edges.
In Tanzania, auto-body repair technicians use circular shearing skills when repairing vehicle body panels. For example, when fixing a damaged car door that has a curved rust spot, a mechanic would use tin snips to cut out the damaged section and shape a replacement patch panel with matching curves. This skill is also used by local metal workers making curved roofing sheets, water tanks, and decorative ironwork in small workshops across the country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawing
- Select tools, equipment and workpieces
- Mark workpieces
- Hold workpieces
- Perform combination sheet metal shearing
- Observe safety precautions
- Clean tools, equipment, workpieces and work place
- Store tools, equipment and remained materials
Tathmini ya matokeo
A circular sheared workpiece conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Take measurement
- Hold and align workpieces
- Handle shearing machine
- Perform circular hand shearing
Principles: The student should state the principles of performing circular hand metal shearing
Theories: The student should:
- Explain the types of shearing machines
- Describe the properties of materials
- Differentiate types of snipers and their applications
- Clarify the purpose of circular shearing
Detailed knowledge about:
- Safety precautions when performing circular hand metal shearing
Swali
Which hand tool is used to cut curved lines and circles in sheet metal during auto-body repair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado