Mada za sehemu hiiPerforming machine shearingMada 2
- Performing straight shearing
- Performing circular shearing
Circular Shearing in Sheet Metal Work
Circular shearing is a sheet metal cutting operation that produces circular disks from flat metal sheets. Unlike straight shearing, which cuts in straight lines, circular shearing uses rotating cutting wheels to cut the metal into circular shapes. The sheet metal is fed between two circular blades or wheels that rotate in opposite directions, cutting the metal as it moves through the machine.
Circular shearing is used to create:
- Circular disks for wheel covers, hub caps, and body panels
- Round blanks for further forming operations
- Circular cutouts for lights, vents, and access panels
- Gaskets and washers from metal sheets
The following tools and equipment are required for circular shearing:
- Shearing machine (circular shear type)
- Working drawing table
- Steel ruler
- Measuring tape
- Scriber
- Try square
- Straight edge
- Centre punch
- Ball pein hammer
- Soft hammer
- Work bench
Always wear the following protective equipment:
- Leather gloves
- Leather apron
- Safety boots
Step 1: Interpret the Drawing
Study the working drawing carefully to determine the required diameter of the circular disk. Calculate the material needed, considering economical use of the metal sheet.
Step 2: Select Tools and Equipment
Choose the appropriate tools from the list above. Check that all measuring tools are in good condition and readable.
Step 3: Select and Prepare Materials
Select the correct type and thickness of sheet metal as specified in the drawing. Common materials include:
- Mild steel plate
- Galvanized plate
- Aluminum sheet
Clean the surface of the metal to remove any dirt, oil, or rust that could affect marking out accuracy.
Step 4: Mark Out the Workpiece
Using a scriber, steel ruler, and try square:
- Measure and mark the centre point of the circle on the metal sheet
- Draw the required diameter using a compass or by marking points around the centre
- Verify measurements with the steel ruler
- Use a centre punch to mark the centre point firmly
Step 5: Set Up the Machine
- Position the shearing machine on a stable work bench
- Check that the cutting wheels are clean and free from damage
- Adjust the blade clearance according to the metal thickness (typically 0.02-0.05mm for thin sheets)
- Ensure the machine is properly secured
Step 6: Position the Workpiece
Place the marked metal sheet on the machine table with the marked circle aligned with the cutting path. Ensure the sheet is flat and held securely.
Step 7: Perform the Cutting
- Start the machine and slowly feed the metal into the rotating cutting wheels
- Keep a steady hand and maintain consistent feeding speed
- Rotate the sheet as needed to follow the circular pattern
- Continue cutting until the complete circle is separated
Step 8: Inspect the Cut Piece
- Check the diameter of the cut disk with a steel ruler
- Verify the edge quality - it should be clean without burrs
- Use a try square to check for any distortion
- If edges are sharp, use a soft hammer to deburr or file lightly
Problem: A student needs to cut a circular disk of 150mm diameter from a galvanized plate measuring 300mm × 300mm × 0.8mm.
Solution:
-
Marking out:
- Find the centre of the 300mm × 300mm plate (at 150mm from each edge)
- From the centre, measure and mark a radius of 75mm (half of 150mm)
- Draw the circle using a compass or by marking multiple points at 75mm from centre
- Mark the centre point firmly with a centre punch
-
Setting blade clearance:
- For 0.8mm galvanized plate, set blade clearance to approximately 0.03-0.04mm
-
Cutting:
- Position the circle on the machine
- Feed the metal steadily through the rotating wheels
- Complete the full circle to separate the disk
-
Checking:
- Measure the diameter in two directions (should be 150mm)
- Check that the edge is clean and not distorted
Regular maintenance ensures accurate cuts and extends machine life:
- Clean the cutting wheels and surrounding areas after each use
- Check the blades for wear or damage before each operation
- Apply lubricant to moving parts regularly
- Ensure blades are properly aligned
- Keep a maintenance log recording inspection dates and any repairs
| Fault | Possible Cause | Remedy |
|---|---|---|
| Irregular circle | Inconsistent feeding speed | Maintain steady, even feeding |
| Burrs on edge | Blade clearance too large | Adjust clearance smaller |
| Diameter too small | Marking error | Re-measure and mark correctly |
| Distorted edges | Too fast feeding | Slow down the feeding speed |
In Tanzania, circular shearing skills are used in local panel beating workshops and auto repair garages across cities like Dar es Salaam, Arusha, and Mwanza. When a motorcycle or vehicle body panel (such as a wheel well or engine cover) needs replacement, a trained auto-body technician uses circular shearing to cut the correct-sized metal disk from a sheet. For example, a small garage in Mwanza might cut a 200mm diameter disk from a 1mm mild steel sheet to repair a damaged motorcycle fender, costing the customer around TSh 15,000-25,000 for the custom-cut part plus labor.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Select suitable materials and sizes
- Take measurements
- Mark out
- Check sharpness and tightness of blade
- Cut the metal
- Check accuracy of cuts
- Observe safety precautions
- Clean tools and equipment
- Clean work place
- Store tools and equipment safely
Tathmini ya matokeo
A circular machine sheared metal conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Take measurements
- Mark workpieces
- Perform machine setting
- Perform circular machine shearing
Principles: The student should explain the principles of performing machine circular shearing
Theories: The student should:
- Describe properties of metals
- Identify parts and functions of shearing machines
- Describe the measuring techniques
- Explain calculation methods for allowances
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing the task
Swali
What is circular shearing in sheet metal work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado