Mada za sehemu hiiPerforming metal brazing and bronze weldingMada 3
- Joining metal into butt joint
- Joining metal into lap joint
- Joining metal into flat position
A welding position is a technique of joining metals from different angles. There are four main welding positions: flat, horizontal, vertical, and overhead. Each position requires different skills because the welder works against or with gravity.
Flat position welding is used when the workpiece lies on the floor or workbench, with the weld metal deposited from above. This position is considered the most accessible because you are not fighting gravity. The flame or arc points upward, and the molten metal stays in place easily.
Why Flat Position is Important
- Easiest position for beginners to learn
- Allows good visibility of the joint
- Molten filler metal flows naturally into the joint
- Less fatigue for the welder
To make a good weld in flat position, you must:
- Maintain a consistent tip angle — keep the torch at a 45° angle to the workpiece
- Keep the flame position steady — the flame should be centered on the joint
- Use consistent motion — move the torch slowly and evenly along the weld line
- Control the heat — too much heat causes burn-through, too little creates weak joints
Before starting flat position brazing or bronze welding, gather:
- Oxy-acetylene welding plant
- Welding torch with appropriate tip
- Pressure regulator
- Hose pipes
- Bronze welding rod (filler metal)
- Flux (Anti-Borax No. 2)
- Wire brush or emery cloth for cleaning
- Clamps to hold the workpiece
- Welding goggles and gloves
Step 1: Prepare the Surface
Clean the metal surfaces to be joined using a wire brush or emery cloth. Remove all dirt, rust, grease, and oil. Clean surfaces ensure strong bonding.
Step 2: Fit and Clamp the Joint
Position the two metal pieces in the desired joint configuration (butt joint or lap joint). Clamp them securely so they do not move during welding. Make sure there is no gap larger than 10% of the metal thickness.
Step 3: Apply Flux
Apply bronze welding flux to the joint area. The flux removes dirtiness, helps the molten bronze flow easily, and protects the molten metal from oxidation.
Step 4: Heat the Joint
Light the torch and adjust to a neutral flame. Hold the flame tip at a 45° angle to the workpiece. Heat the joint uniformly until the metal reaches the correct temperature — the flux will begin to sizzle or turn clear.
Step 5: Add the Filler Metal
Touch the bronze rod to the heated joint area. As the metal gets hot enough, the bronze will melt and flow into the joint. Keep adding filler metal while moving along the joint.
Step 6: Cool and Clean
Allow the weld to cool naturally. Do not quench with water. After cooling, clean the weld with a wire brush to remove any flux residue.
A student at VETA Manyara needs to join two pieces of body panel metal, each 1mm thick, to repair a damaged car door. The pieces are placed flat on the welding bench in a butt joint configuration.
- The student cleans both metal edges with emery cloth.
- The student clamps the pieces so they touch along the edge.
- The student applies Anti-Borax flux along the joint.
- The student heats the joint with the torch at 45° until the flux melts.
- The student touches the bronze rod to the joint — it melts and fills the gap.
- The student moves slowly along the joint until fully welded.
The result is a strong bronze weld that joins the panels without melting the base metal, avoiding distortion.
- Using wrong flux or no flux at all
- Overheating the base metal until it melts
- Moving the torch too fast, leaving gaps in the weld
- Failing to clean the metal before welding
- Welding with the tip at the wrong angle
In Tanzania, auto body repair shops in Dar es Salaam, Arusha, and Mwanza use flat position bronze welding to repair car body panels without causing heat distortion. For example, when fixing a rusty door panel on a Toyota Wish taxi, a mechanic places the panel flat on the bench, cleans it, applies flux, and uses bronze welding to fill small holes or cracks. This skill helps local mechanics earn income by restoring vehicles for bus and daladala operators who need quick, affordable repairs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Inspect gas welding equipment
- Choose suitable materials
- Assemble gas cylinder
- Select nozzle sizes
- Select welding rods (bronze rods)
Tathmini ya matokeo
Ferrous metal joined on flat position using bronze welded as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should highlight the procedures required to:
- Take measurements
- Mark workpieces
- Make joints
- weld metals on flat position by hard soldering/brazing
- Orient on different welding positions
Principles: The student should explain the principles of:
- Obtaining good fusion on metals
Swali
What is the flat position in welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado