Mada za sehemu hiiPerforming gas welding on vehicle body panelsMada 4
- Welding metals in butt joint on horizontal position
- Welding metals into lap joint on horizontal position
- Welding metals in corner joint on vertical position
- Welding metals in lap joint on overhead position
Overhead position gas welding is performed on the underside of workpieces that are positioned above the welder's head. In auto body repair, this position is common when welding under vehicle roofs, body panels, or any component that cannot be moved to a convenient height. This is one of the most challenging welding positions because the molten metal must be deposited while fighting against gravity.
When welding in an overhead position, the molten metal naturally wants to fall due to gravity. This creates two main problems:
- Risk of injury: Molten metal can drip onto the welder's body causing burns
- Poor weld quality: The molten metal may form large sags or create beads with a high crown instead of a smooth, uniform weld
Because of these challenges, overhead welding requires extra care and proper technique to produce a strong, quality weld.
Before starting, gather all required tools and materials:
Materials:
- Two mild steel sheets (60 mm × 40 mm × 4 mm)
- Six filler rods (3.2 mm diameter is common)
Tools and Equipment:
- Oxy-acetylene welding plant
- Pressure regulator
- Welding torch with appropriate nozzle
- Hose pipes
- Cylinder key
- Spark lighter
- Wire brush
- Chipping hammer
- Clamps
- Marker and tape measure
Personal Protective Equipment (PPE):
- Clear goggles
- Leather gloves
- Safety boots
- Canvas spats
- Dust mask
- Overalls
Before welding, follow these important safety measures:
- Ensure the work area is free from grease, oil, dust, and flammable materials
- Wear all personal protective equipment properly
- Check all connections for leaks using a bubble soap leak detector
- Ensure proper ventilation in the work area
- Keep a fire extinguisher nearby
- Allow the workpiece to cool after welding or use tongs to dip it in water
Follow this procedure carefully under your teacher's supervision:
Step 1: Prepare the Workpieces
- Select proper materials, tools, and equipment
- Clean both workpieces free from oil, grease, and dirt using a wire brush
- Position the workpieces so that one overlaps the other (this is the lap joint configuration)
- Clamp the overlapped workpieces in a horizontal position at a height that can be reached above your head
Step 2: Set Up the Welding Plant
- Assemble the oxy-acetylene plant following proper procedures
- Select the proper welding tip according to the workpiece thickness
- Light the torch using a spark lighter (never use a matchbox)
- Adjust the flame to a neutral flame (white cone with luminous outer envelope)
Step 3: Position the Torch and Filler Rod
- Hold the gas torch nozzle with your right hand at an angle of 45° from the vertical of the two metal strips
- Hold the filler rod with your left hand at an angle of 30° to the vertical
Step 4: Make Tack Welds
- Heat the joint of both base metals with the neutral flame until they reach a red-hot condition
- Bring the filler rod and heat its end until fusion takes place
- Make a tack weld at the starting point (left end) of the joint
- Make another tack weld at the opposite end (right end)
Step 5: Run the Weld
- Starting from the right side, steadily move the gas flame over the joint toward the left
- Feed the filler rod continuously into the molten pool
- Maintain a steady hand movement to create a uniform weld bead
- Work steadily from right to left until the entire joint is welded
Step 6: Finish the Weld
- Allow the workpiece to cool or dip it in water using tongs
- Gently tap the weld bead with a chipping hammer to remove slag
- Clean the workpiece thoroughly with a wire brush
- Assess the quality of the weld
A student needs to weld two overlapping mild steel sheets (each 60mm × 40mm × 4mm) in an overhead position to repair a vehicle roof panel.
Procedure followed:
- The student cleans both sheets and clamps them so that one sheet overlaps the other by about 20mm
- The workpieces are positioned horizontally at head height
- The student lights the torch and adjusts to a neutral flame
- Holding the torch at 45° from vertical and filler rod at 30°, the student heats both metal surfaces until red-hot
- Tack welds are made at both ends to hold the pieces in place
- Starting from the right, the student moves the flame steadily while adding filler rod, completing the weld from right to left
- After cooling, slag is removed and the weld is cleaned and inspected
The resulting weld should be uniform, without excessive sags or overlaps, and should create a strong bond between the two overlapping sheets.
Be aware of these problems that can occur:
- Excessive sag: Molten metal drooping due to gravity
- Porosity: Gas pockets trapped in the weld metal
- Incomplete fusion: Failure of the filler rod to properly fuse with base metals
- Undercut: Grooves burned into the base metal at the weld edge
- Use a slightly smaller filler rod diameter than you would for horizontal welding
- Keep the flame moving steadily to prevent molten metal from accumulating
- Maintain shorter weld beads to control the molten pool
- Work in short sections rather than long continuous beads
In Tanzania, auto body repair technicians frequently use overhead lap joint welding when fixing rust damage on vehicle roof panels, repairing door frames, or joining interior panels under the dashboard. For example, when a daladala (minibus) roof develops rust holes, a technician in Dar es Salaam would weld overlapping patches in the overhead position to create a watertight seal, restoring the vehicle's structural integrity and extending its usable life on the road.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Inspect gas welding equipment.
- Assemble gas cylinder.
- Select nozzle sizes.
- Select welding rods.
- Cut plate to specifications.
- Light the torch and Adjust welding flames.
- Align a workpiece in lap joint on overhead position.
- Weld the joint.
- Keep on maintaining movement of torch and rod
Tathmini ya matokeo
Workpieces welded in lap joint on overhead position conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Weld metals by gas flame
- Weld metals in lap joint
- weld in overhead position
- Set welding flame
- Perform gas welding in overhead position
Principles: The student should describe the principles of:
- Welding metals by gas flame
- Setting welding flame
Theories: The student should:
- Identify parts of gas welding equipment and their functions
- Suggest recommended working flames and pressure
- Describe the side effects of back fire and flash back
- List down different welding procedures and techniques
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while doing the task.
Swali
What does the term "overhead position" refer to in gas welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado