Mada za sehemu hiiCarrying out mild steel arc weldingMada 9
- Welding straight beads
- Welding metal in down hand butt joint
- Welding metal in down hand lap joint
- Welding metal in down hand corner joint
- Welding metal in down hand tee joint
- Welding metal in a horizontal butt joint
- Welding metal in horizontal tee joint
- Welding metal in horizontal lap joint
- Welding metal in horizontal corner joint
Welding Straight Beads
Arc welding is a fundamental process used to join metal parts in vehicle body repair. This note covers the essential concepts, tools, materials, and procedures for welding straight beads—the foundation of quality arc welding.
Arc welding uses an electric arc to create intense heat between the welding electrode and the metal workpiece. The heat melts both the electrode and the base metal, fusing them together to form a strong joint. When you move the electrode along the metal at the correct speed and distance, you create an even layer of molten metal called a weld bead. The appearance, uniformity, and integrity of this bead indicate the quality of the weld.
Understanding electrical terms is essential for controlling the welding process:
- Amperage: The unit measuring the amount of electricity flowing through the welding circuit. It determines the heat or power of the welding machine.
- Voltage: The electrical pressure or force that causes current to flow through the circuit.
- Alternating Current (AC): Current that changes direction repeatedly. Most commercial power supplies use 60-cycle AC (60 direction reversals per second).
- Direct Current (DC): Current that flows in one direction only—from the negative terminal through the circuit to the positive terminal.
Transformer Welding Machine
A transformer takes electrical current from the main power source and converts it to the voltage level suitable for welding. It delivers alternating current (AC).
Direct Current (DC) Generator
A DC generator converts mechanical energy into electrical energy. It produces direct current suitable for welding applications.
Follow these steps to assemble the welding machine safely:
- Select proper materials, tools, and equipment.
- Wear personal protective equipment (PPE) accordingly.
- Use the manufacturer's manual guidelines.
- Connect the electrode holder cable to the positive (+) terminal.
- Connect the ground cable with the workpiece clamp to the negative (−) terminal.
- Attach the electrode to the electrode holder.
- Turn on the machine and set the current according to material specifications.
Safety Note: Avoid direct contact with positive and negative terminals to prevent electric short circuits.
Personal Protective Equipment (PPE)
- Welding shield (hand-held or face shield)
- Leather gloves and apron
- Safety boots
- Clear goggles
Hand Tools
- Electrode holder: Holds the electrode and conducts current. Parts include jaw, jaw spreading lever, insulator, spring, heat shield, and handle.
- Earth clamp: Clamps to the workpiece to complete the electrical circuit.
- Chipping hammer: Removes slag from welded joints.
- Wire brush: Cleans rust, scale, paint, and small slag particles from metal surfaces.
- Fire tongs: Holds hot workpieces during welding.
Base Metal
The base metal (also called parent metal) is the primary metal being joined. It melts during welding and fuses with the filler material to form a joint.
Electrode
Electrodes are rod-like sticks that conduct current and melt to provide filler material for the weld. They are coated with flux to protect the weld pool from oxidation. Common types include mild steel electrodes, alloy steel electrodes, and cast iron electrodes.
Striking the Arc
Striking the arc initiates the welding current by briefly touching the electrode to the workpiece and immediately raising it to create a small gap. This gap is called the arc length and determines the heat produced.
Steady Weld Movement
After striking the arc, maintain a constant, even motion along the joint. Both the base metal and electrode melt to form a continuous weld bead.
The arc length—the gap between the electrode and workpiece—directly affects weld quality:
- Voltage: Longer arc length increases resistance and voltage; shorter arc reduces them.
- Heat Input: Too long an arc reduces heat, causing incomplete penetration. Too short an arc overheats the metal, causing distortion and burn-through.
- Penetration: Shorter arc length produces deeper penetration; longer arc produces shallower penetration.
- Bead Appearance: Longer arcs create narrow, rough beads with spatter. Shorter arcs create wider, flatter, more uniform beads.
- Welding Speed: Longer arcs require slower travel; shorter arcs allow faster travel.
Stringer Bead
A narrow, straight bead produced with minimal side-to-side movement. It provides consistent penetration and is commonly used for flat, horizontal, and overhead positions.
Weave Bead
A wider bead produced by moving the electrode side-to-side. It covers a larger surface area in a single pass than a stringer bead.
Materials and Tools
- Mild steel sheet (100 mm × 60 mm × 4 mm)
- Electrode (2.5 mm diameter)
- Welding booth, welding bench, arc welding machine
- Earth clamp, electrode holder
- Chipping hammer, wire brush
- Centre punch, marker
- Personal protective equipment (PPE)
Procedure
- Select proper materials, tools, and equipment.
- Wear PPE (overalls, gloves, boots, apron, face shield).
- Prepare the working area—remove dust, combustible, and flammable materials.
- Prepare the mild steel workpiece (100 mm × 60 mm × 4 mm).
- Place the workpiece on the welding table.
- Clean the welding area with a wire brush.
- Mark the portion to be welded.
- Clamp the workpiece firmly on the welding table.
- Clamp the earth cable to the workpiece.
- Select the correct electrode size and attach it to the electrode holder.
- Turn on the welding machine.
- Strike the arc and perform straight bead welding, keeping your hand and electrode above the workpiece.
- Allow the workpiece to cool.
- Turn off the machine.
- Remove slag from the bead using a chipping hammer and wire brush.
- Assess the quality of the weld bead.
Important: The electrode must be kept away from the workpiece before striking the arc to avoid accidental contact.
In Tanzania, arc welding skills are essential for vehicle repair mechanics in local garages and workshops across regions like Dar es Salaam, Arusha, and Mwanza. For example, a mechanic at a small bodyshop along the Nyerere Road in Dar es Salaam would use straight bead welding to repair damaged vehicle frames and body panels, ensuring roadworthy certifications for cars used for taxi services (daladala) and personal transport.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Inspect the machine, cable and electrode holder
- Interpret working drawing
- Prepare materials for welding.
- Select type and size of electrode for the job.
- Set recommended current.
- Weld a workpiece in down hand straight beads
Tathmini ya matokeo
Welded straight beads conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Perform arc welding
- Minimize distortion
- Obtain good penetration
- Select weld current
- Weld straight bead
Principles: The student should explain the principles involved in welding straight beads
Theories: The student:
- Distinguish types of metals and their properties
- Explain the types and functions of welding equipment
- Describe groove preparations
- Uses of wire brush and chipping hammer
- Clarify the metallurgical effects on weldment
- Explain the Characteristics of AC and DC welding machine.
- Distinguish types of welds
- Distinguish types of electrode coatings and function
- Explain work angle and lead angle
- Identify welding symbols
- Identify types of welding beads
- Present the types of distortion
- Describe joint design
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while welding the workpiece
Swali
What is the primary function of the electrode in arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado