Mada za sehemu hiiMaintaining three wheeled bodyMada 4
- Dismounting three wheeled body
- Repairing three wheeled body
- Mounting three wheeled body
- Aligning three wheeled body
A three-wheeled motorcycle, such as a cargo tricycle or a passenger bajaji, is built on a chassis (frame) that carries the engine, the wheels and the suspension. The body, which may be a cargo box or a passenger cabin, is a separate unit fixed to the chassis by mounts. The body is taken off when the chassis or the body itself has to be straightened, welded or treated for rust. Mounting the three-wheeled body means fitting the body back onto the chassis, fastening it with the correct mounts and reconnecting everything that was disconnected, as the manufacturer's guideline requires. A badly mounted body can shift, rattle, crack the frame or even come loose on the road.
The service manual is the manufacturer's guide for one particular model. Using it saves time, prevents damage and makes the work safe, because it gives:
- The position and type of every body mount
- The size and strength grade of the bolts, and the order of the washers, rubber bushes and nuts
- The tightening torque for each bolt and the order of tightening
- The measurements used to check that the body sits in the right place
- Rigid bolted mounts: brackets on the body are bolted straight to brackets or cross-members on the chassis with strong bolts, washers and lock nuts.
- Rubber-cushioned mounts: a rubber bush or pad sits between the body and the chassis. It absorbs vibration and noise, so it is used for cabins and seats.
- U-bolt and clamp mounts: U-bolts clamp the runners of the body to the chassis rails without drilling the frame.
- Hinged mounts: a tipping cargo box turns on hinge pins at the rear and is held down by a catch at the front.
- Welded brackets: the brackets that carry the mounts are welded to the chassis. Welding is done only where the manufacturer allows it.
- Wear an overall, safety boots, gloves and clear safety glasses. Safety gear protects you from crushed toes, cuts from sheet metal edges and rust or dirt falling into your eyes.
- Park the vehicle on firm, level ground, switch off the engine, remove the key and chock the wheels.
- Support the vehicle on a motorcycle lift or safety stands strong enough for its weight. Never work under a body that is held up only by a jack or by people.
- Disconnect the battery, negative terminal first, before joining any wiring.
- The body is heavy and awkward. Lift it with lifting equipment or with enough people, with one person giving the commands. Bend your knees, keep your back straight and lift together.
- Keep your fingers out of the gap between the body and the chassis. Use an aligning bar, not a finger, to line up bolt holes.
- Tool kit: ring and open-ended spanners, sockets and ratchet, screwdrivers, hammer
- Torque wrench
- Special aligning tools, such as an aligning bar or tapered drift
- Measuring tape and wire brush
- Motorcycle lift or safety stands, and wheel chocks
- Service manual
- New bolts, lock nuts and rubber mounts where the old ones are worn
- Inspect the chassis, especially the mounting brackets and cross-members, for cracks, bends, rust and poor welds. Faults must be repaired before the body goes on.
- Inspect the body brackets and floor. Bolt holes that have worn oval will let the body move.
- Clean the surfaces where the body meets the chassis with a wire brush, and paint any bare metal to stop rust.
- Replace rubber mounts that are cracked, hardened or soaked with oil, and bolts that are rusted, bent or have damaged threads. Use bolts of the size and grade given in the manual, and fit new lock nuts.
- Place the mounts. Put the rubber pads, bushes and spacers on the chassis brackets in the order shown in the manual.
- Lower the body. Lift the body over the chassis and lower it slowly, with a helper at each corner guiding it onto the mounts.
- Start every bolt. Line up the holes with the aligning bar. Fit all the bolts with their washers and nuts, and tighten them by hand only.
- Check the position. Measure from the body to the chassis rail or the rear wheel on each side. The two sides should be equal, the body should sit level, and nothing should touch the tyres, chain, exhaust or suspension.
- Tighten. Tighten the bolts a little at a time, working across the body from one corner to the opposite corner. Finish with the torque wrench at the torque given in the service manual. Never guess the torque: a loose bolt lets the body move, and an over-tightened bolt strips the thread or crushes the rubber mount.
- Reconnect. Join the wiring for the rear lamps, brake lamp and indicators, and clip it away from hot and moving parts. Refit any cables, mudguards, seats or tailgate that were removed, then reconnect the battery.
- Test. Lower the vehicle to the ground. Check that all the lamps and the brakes work. Rock the body by hand: there should be no movement or knocking. Under supervision, drive slowly in a safe area away from traffic, then check the bolts again.
- Tightening one bolt fully before the others are started, which pulls the body out of line
- Reusing damaged bolts, worn lock nuts or perished rubber mounts
- Trapping wires or cables between the body and the chassis
- Mounting a body on a cracked or bent chassis
A cargo tricycle in Arusha has had a cracked cross-member welded, and the cargo box must go back on. The mechanic chocks the wheels and checks the repaired weld. She finds two rubber mounts split and replaces them. Four people lower the box onto the mounts while she guides the holes with an aligning bar. She starts all the bolts by hand, measures the gap between the box and each rear tyre, and finds it equal on both sides. She tightens the bolts corner to corner, finishing with the torque wrench at the figure given in the manual. She reconnects the rear lamp wiring and the battery, and tests the lamps and brakes. After a slow test drive in the yard, she checks every bolt again.
- Wipe oil and dirt off the tools and return them to the tool kit or tool board. Set the torque wrench back to its lowest setting before storing it.
- Lower the lift and put the stands and chocks back in their place.
- Sweep the floor and wipe up any oil so that nobody slips.
- Put old bolts and scrap metal in the scrap bin, and worn rubber mounts and oily rags in the correct covered waste bins. Never burn rubber or oily waste.
Cargo tricycles carry tomatoes, cassava, water and building materials in many Tanzanian towns, and their bodies take heavy knocks. A mechanic in Mwanza who can remove a damaged cargo box, repair it and mount it again correctly keeps these vehicles earning for their owners.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools and equipment
- Carry out chassis inspection
- Dismantle three-wheel inspection
- Repair three-wheel body
- Weld three-wheel body
- Assemble three-wheel body
- Align three-wheel body
- Test three-wheel body
- Clean tools, equipment and workplace
- Store and keep tools and equipment
Tathmini ya matokeo
Three wheeled body mounts as per manufacturer’s guideline
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Mount three wheeled body
Principles: The student should explain the principles of: Mounting three wheeled body
Theories: The student should explain:
- Advantages of using service manual
- Types of Mounts three wheeled body
- Importance of using safety gears
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while servicing three wheeled body.
- Handling of tools and equipment
- Waste disposal
Swali
Which type of body mount is chosen for cabins and seats because it absorbs vibration and noise?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado