Mada za sehemu hiiCarrying out gear box dismantlingMada 2
- Dismounting gear box
- Dismantling gear box
Dismounting Gear Box
Dismounting a gear box is the process of removing the transmission assembly from a motorcycle for inspection, repair, or replacement of worn parts. This is a fundamental skill in motorcycle mechanics that allows technicians to access internal components such as gears, bearings, and shafts for maintenance.
By the end of this lesson, you should be able to:
- Prepare the motorcycle and workspace for gear box dismounting
- Select and use appropriate tools safely
- Follow the correct sequence to remove the gear box from the motorcycle
- Handle removed parts with care to prevent damage
Before starting any work, always observe these safety measures:
- Wear protective gear: overall, safety boots, gloves, and safety clear glasses
- Ensure the motorcycle is stable on a central stand or work bench
- Disconnect the battery to prevent electrical accidents
- Allow the engine and exhaust to cool down if recently run
- Work in a well-lit and ventilated area
The following tools and materials are needed for dismounting a gear box:
- Service manual for the specific motorcycle model
- General tool kit (spanners, sockets, screwdrivers)
- Snap ring pliers for removing retaining clips
- Torque wrench for proper tightening
- Air compressor for cleaning parts
- Clean cotton waste or rags
- Kerosene for cleaning oily parts
- Fresh oil for lubrication after reassembly
Step 1: Prepare the Motorcycle
Park the motorcycle on a stable stand and ensure it is level. Cover nearby body panels with cloth to protect them from scratches and dirt. Refer to the service manual to identify the gear box location and all fasteners that need removal.
Step 2: Drain the Lubricant
Locate the gear box drain plug and place a container underneath. Remove the drain plug using the appropriate spanner and allow all oil to drain completely. This prevents oil spillage during removal and contamination of the workspace.
Step 3: Disconnect Related Components
Remove any components that obstruct access to the gear box, such as:
- Foot pegs and gear shift lever
- Chain cover or sprocket cover
- Engine mounting bolts (if integrated with gear box)
- Electrical connectors to gear position sensor
Label disconnected wires and cables for easy reassembly.
Step 4: Support the Gear Box
Place a suitable jack or wooden block under the gear box to support its weight during removal. Ensure it is stable before proceeding.
Step 5: Remove Mounting Bolts
Using the correct size spanner or socket, remove all gear box mounting bolts. Work in a diagonal pattern when removing bolts to prevent uneven stress. Keep bolts organized in a tray to avoid loss.
Step 6: Separate the Gear Box
With all bolts removed, gently slide the gear box away from the engine. Use a rubber mallet if needed to tap the case lightly—never use excessive force. If the gear box is stuck, check for missed bolts or cables.
Step 7: Place on Work Bench
Carefully lower the removed gear box onto a clean work bench or tray. Cover with clean cotton waste to protect from dust and debris.
A motorcycle rider in Dar es Salaam brings in a Yamaha bike that has difficulty shifting gears and makes grinding noises. As the mechanic, you decide to inspect the gear box internally.
- You park the bike, wear your safety boots and gloves
- Drain the gear oil into a container (you collect about 750 ml)
- Remove the chain cover and gear shift lever
- Support the gear box with a jack
- Remove six mounting bolts (10 mm, 12 mm, and 14 mm sizes)
- Carefully slide the gear box out and place it on the work bench
Now you can open the gear box case to inspect the gears and bearings for wear or damage.
- Always consult the service manual for your specific motorcycle model
- Keep all removed fasteners organized and labelled
- Use cotton waste to clean oil from components, not bare hands
- Never force components during removal—check for missed connections
- Clean all parts with kerosene before inspection
- Forgetting to drain oil before removal
- Not wearing safety gear during the procedure
- Misplacing small bolts and circlips
- Using wrong tool sizes that can damage fasteners
In Tanzania, motorcycle taxis (bodaboda) are widely used for transport in cities like Dar es Salaam, Mwanza, and Arusha. When a bodaboda rider experiences gear slipping or difficulty shifting, a local mechanic must dismount the gear box to diagnose the problem. This skill enables the mechanic to earn income by offering repair services, keeping the bodaboda operators working and supporting their families.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools and equipment
- Dismount gear box
- Clean gear box
- Detach parts of gear box
- Check gear box worn out components
- Clean tools, equipment and work place
- Store tools, parts and equipment
Tathmini ya matokeo
Gear box dismounted as per manufacturer’s guideline
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Dismount motorcycle gear box
Principles: The student should explain the principles of: Dismounting gear box
Theories: The student should explain: -
- checking gear box
- Importance of testing gear box
- Importance of observing safety precaution
Detailed knowledge about:
- Safety precautions while dismounting gear box
- Safe handling of tools and equipment
Swali
Which of the following safety precautions must be observed BEFORE starting to dismount a motorcycle gear box?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado