Mada za sehemu hiiPerforming arc weldingMada 4
- Performing down hand arc welding bead
- Performing down hand V joint
- Performing down hand butt joint
- Performing down hand T joint welding
Performing Down Hand Arc Welding Bead
Down hand arc welding, also called flat position welding, is the most basic and easiest welding position where the metal lies flat on the welding bench and the welder works from above. This technique is commonly used in motorcycle repair workshops in Tanzania for joining frame parts, exhaust brackets, and other flat components.
Before starting any welding work, always observe these safety rules:
- Wear welding helmet with proper shade lens (usually shade 10-12)
- Put on leather welding gloves
- Wear leather apron or welding jacket
- Use steel-toed safety boots
- Ensure good ventilation in the work area
- Remove all flammable materials from the welding zone
- Keep a fire extinguisher nearby
- Check all cables for cuts or damage before connecting
The following tools and equipment are needed for performing down hand arc welding:
- AC/DC arc welding machine – provides the electric current needed to create the arc
- Welding electrodes – typically 3.2mm diameter for general work
- Electrode holder – clamps the electrode and conducts current
- Welding bench – stable flat surface for positioning workpieces
- Clamps – hold the metal pieces firmly in place
- Chipping hammer – removes slag from the weld bead
- Wire brush – cleans the weld area and removes rust
- Hand hacksaw or shearing – cuts metal to size
- Earth clamp – connects the workpiece to the welding machine
- Protective equipment – helmet, gloves, apron
1. Clean the Workpiece
Use the wire brush to clean both sides of the metal surfaces to be joined. Remove rust, paint, oil, and dirt. A clean surface ensures a strong weld.
2. Fit the Electrode
Insert the correct electrode into the holder. For beginners, a 3.2mm diameter electrode is suitable. Make sure the electrode is tightly secured.
3. Set the Welding Current
Adjust the welding machine to the appropriate current setting. For 3.2mm electrodes on mild steel plate (2-3mm thick), set between 80-100 amps. Start with a lower setting and adjust as needed.
4. Position the Workpiece
Place the metal pieces on the welding bench in the correct position. Use clamps to hold them firmly together. For a butt joint, ensure proper gap (about the thickness of the metal). For lap joint, overlap the pieces properly.
5. Connect Earth Clamp
Attach the earth clamp firmly to the workpiece. Ensure good electrical contact.
Correct Body Position
- Stand comfortably with your feet shoulder-width apart
- Keep your leading arm steady by tucking it close to your body
- Maintain a consistent viewing angle to the weld pool
Electrode Angle
Hold the electrode at 70-80 degrees from the workpiece surface. The angle should be slightly tilted in the direction of travel. This angle helps:
- Good penetration into the joint
- Proper shielding of the weld pool
- Smooth bead formation
Arc Length
Maintain an arc length of approximately 2-3mm. A too-short arc causes sticking, while a too-long arc produces a wandering, porous weld with excessive spatter.
Travel Speed
Move the electrode at a steady, uniform speed. The ideal speed produces a bead that:
- Has even width throughout
- Shows uniform ripples
- Has good penetration without excessive reinforcement
If you move too fast → insufficient penetration, narrow bead If you move too slow → excessive penetration, a tall and wide bead, potential burn-through
Stringer Bead Technique
For a basic down hand weld, use the stringer bead technique:
- Strike the arc by briefly touching the electrode to the workpiece and quickly raising it
- Let a small molten pool form at the starting point
- Begin moving forward along the joint at a constant speed
- Keep the arc length constant
- Watch the weld pool and adjust speed as needed
- Finish the bead by lifting the electrode to break the arc
| Defect | Cause | Prevention |
|---|---|---|
| Porosity (holes) | Dirty metal, too long arc, damp electrodes | Clean metal, correct arc length, store electrodes dry |
| Lack of penetration | Too fast travel, low current, too large gap | Reduce speed, increase current, fit pieces closer |
| Excessive spatter | Arc too long, current too high | Maintain correct arc length, reduce current |
| Uneven bead | Inconsistent speed, unstable hand | Practice steady hand movement, maintain constant speed |
| Cracks | Rapid cooling, wrong electrode | Allow slow cooling, use correct electrode type |
A motorcycle frame repair shop in Dar es Salaam needs to repair a cracked exhaust bracket. The bracket is a 3mm thick mild steel plate. The welder:
- Cleans the cracked area with a wire brush
- Clamps the bracket on the welding bench
- Uses a 3.2mm electrode set at 90 amps
- Strikes the arc and makes a stringer bead along the crack
- Maintains 75-degree electrode angle and 2mm arc length
- Moves at steady speed to produce a uniform bead
- Chips off slag and brushes the weld clean
- Inspects for defects
The resulting weld shows even ripples, good penetration, and no visible defects—confirming a successful down hand arc welding bead.
In Tanzania, down hand arc welding is essential for motorcycle repair shops across the country—from Kibaha to Mwanza. A small motorcycle garage in Arusha would use this skill to repair broken foot pegs, fix cracked engine guards, or weld loose exhaust brackets, keeping motorcycles roadworthy and saving riders the cost of buying new parts.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools, equipment and materials
- Select welding current
- Weld work piece
- Remove slag
- Observe safety precautions
- Clean tools, equipment, work piece, and work place.
- Store tools and 55
Tathmini ya matokeo
down hand arc welding bead as per given instruction
- Performing welding bead.
- Types of electrodes
- Properties of materials.
- Application of AC and DC arc machines Circumstantial knowledge Detailed knowledge about: Safety precautions while performing arc
- Safe handling of work tools, equipment and
- Proper waste disposal
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Prepare work piece. Performing down hand arc welding bead
Principles: The explain the principles of:
Theories: The explain:
- Scriber
- Centre punch.
- Steel rule
- Internet connectivity
- Set of files
- Try square
- Grinding machine
- Anvil
- Welding shield.
- Leather apron
- Tong
- Gloves Safety boots Overall
- Safety clear glasses
Swali
What is another name for down hand arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado