Mada za sehemu hiiDetermining characteristics of passive electronic componentsMada 3
- Checking characteristics of resistor
- Checking characteristics of capacitor
- Checking characteristics of inductor
A resistor is a passive electronic component that limits or regulates the flow of electric current in a circuit. Checking resistor characteristics involves measuring its resistance value, verifying it is within acceptable limits, and testing for faults such as open or short circuits.
A resistor is a two-terminal component designed to provide a specific amount of resistance to the flow of current. Resistance is measured in Ohms (Ω). Resistors are used in motorcycle electrical systems to:
- Limit current flow to protect sensitive components
- Divide voltages in circuits
- Control the brightness of indicator lights
- Set timing circuits for electronic ignition systems
Fixed Resistors
Fixed resistors have a constant resistance value that cannot be changed. The most common type is the carbon film resistor, which has a beige or tan body with colored bands that indicate its value.
Variable Resistors
Variable resistors allow the resistance to be adjusted manually. They include:
- Potentiometers: Used for volume controls and throttle position sensors
- Thermistors: Resistance changes with temperature (used in temperature sensors)
- Photoresistors: Resistance changes with light intensity
Resistors use colored bands to indicate their resistance value. The color code is read from left to right:
| Color | Digit | Multiplier | Tolerance |
|---|---|---|---|
| Black | 0 | 1Ω | — |
| Brown | 1 | 10Ω | ±1% |
| Red | 2 | 100Ω | ±2% |
| Orange | 3 | 1kΩ | ±3% |
| Yellow | 4 | 10kΩ | ±4% |
| Green | 5 | 100kΩ | ±0.5% |
| Blue | 6 | 1MΩ | ±0.25% |
| Violet | 7 | 10MΩ | ±0.1% |
| Grey | 8 | — | ±0.05% |
| White | 9 | — | — |
| Gold | — | 0.1Ω | ±5% |
| Silver | — | 0.01Ω | ±10% |
Worked Example
A resistor has four color bands: Brown, Black, Red, Gold.
- First band (Brown) = 1
- Second band (Black) = 0
- Multiplier (Red) = 100Ω
- Tolerance (Gold) = ±5%
Calculation: R=10×100Ω=1000Ω=1kΩ
The actual resistance can range from 950Ω to 1050Ω (5% tolerance).
Required Tools
- Digital or analogue multimeter
- Resistor under test
- Safety gloves and boots
Safety Precautions
- Always disconnect power from the circuit before testing
- Remove the resistor from the circuit when possible for accurate readings
- Wear safety gloves to avoid electric shock
- Ensure the workbench is clean and dry
Procedure
-
Select the resistor to be tested and observe its color bands to determine the expected value.
-
Set the multimeter to resistance mode (Ω). Start with a higher range and adjust downward for better accuracy.
-
Connect the probes — place the red probe on one terminal and the black probe on the other terminal of the resistor.
-
Read the display — note the measured resistance value.
-
Compare the reading with the expected value from the color code. The resistor is good if the measured value falls within the tolerance range.
-
Check for faults:
- Open resistor: Display shows "1" or infinite resistance — the resistor has failed
- Short resistor: Display shows zero or near-zero resistance — the resistor has failed
- Intermittent fault: Resistance fluctuates — the resistor is faulty
Worked Example
You test a resistor with color bands: Yellow, Violet, Orange, Silver.
- Expected value: 47×1000Ω=47kΩ
- Tolerance: ±10% (Silver)
- Acceptable range: 42.3kΩ to 51.7kΩ
The multimeter reads 46.5kΩ. This is within the acceptable range, so the resistor is good.
An oscilloscope can display how a resistor behaves in an active circuit. Connect the oscilloscope probes across the resistor to observe:
- Voltage waveform across the resistor
- Current flow patterns (using Ohm's law: I=V/R)
- Any signal distortion caused by the resistor
This is useful for testing resistors in ignition control and sensor circuits.
A curve tracer plots the voltage-current (V-I) characteristic curve of a resistor. For an ideal resistor, this produces a straight line. Deviations from a straight line indicate:
- Non-linear behavior
- Thermal issues
- Partial open or short conditions
| Fault | Multeter Reading | Possible Cause |
|---|---|---|
| Open | Display shows "1" or ∞ | Burned out, broken wire inside |
| Low resistance | Much lower than expected | Internal short, damage |
| Intermittent | Fluctuating readings | Loose connection, damaged element |
| Noisy | Unstable reading | Corrosion, physical damage |
In Tanzania, checking resistor characteristics is essential when repairing motorcycle electrical systems such as indicator lights, horn circuits, and electronic ignitions. For example, if a motorcycle's headlight is dim, a mechanic in Dar es Salaam would use a multimeter to test the resistor (or current-limiting component) in the lighting circuit to determine whether it is within specification or needs replacement, ensuring the headlight functions properly for safe night driving.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select relevant safety gears, tools and equipment
- Select resistor.
- Test resistor
- Record test results
- Interpret standard test
- Observe safety 76 regulations.
- Clean tools, equipment and workplace
- Store tools, components
Tathmini ya matokeo
Characteristics checked and recorded as per instruction.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Check characteristics of resistor
- Perform colour code identification
Theories: The explain:
- Types of resistors.
- Characteristics of
- resistor symbol.
- Applications of
- Variation of performance with temperature.
- Safety precautions in determining resistor.
- Safe handling of tools, test equipment and measuring instruments
Swali
What is the SI unit used to measure electrical resistance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado