Mada za sehemu hiiPerforming engine maintenanceMada 2
- Changing engine oil
- Carrying out valve adjustment
Changing Engine Oil
Engine oil is a lubricant used in internal combustion engines to reduce friction, prevent wear, and enhance performance. It is a critical fluid that keeps the moving parts of an engine working smoothly and efficiently.
Engine oil performs several important functions in a motor vehicle engine:
- Lubrication: Engine oil lubricates the engine's moving parts by reducing friction, allowing the engine to run smoothly and efficiently.
- Cooling: Engine oil cools the engine by dissipating heat generated from engine operation, preventing overheating.
- Cleaning: Engine oil contains detergents and dispersants that help keep the engine clean by preventing the buildup of sludge and deposits.
- Sealing: Engine oil improves the seal between the piston rings and cylinder walls, enhancing compression and efficiency.
- Corrosion Protection: Engine oil forms a protective film on engine components to prevent rust and corrosion.
There are three main types of engine oil available:
Conventional Engine Oil
These are hydrocarbon-based oils produced from crude oil. They contain many cleansing and anti-corrosion additives. However, due to the inherent impurities and molecular irregularities of crude oils, conventional oils have less performance than synthetic oils and require more frequent oil changes.
Synthetic Engine Oil
Synthetic engine oils consist of the same molecular chain of hydrocarbon molecules as conventional oils but are capable of operating at higher and lower temperatures. They resist breakdowns caused by high temperatures and remain cleaner for a much longer time compared to conventional oils.
Synthetic Blended Engine Oil
Synthetic blended engine oil is a mixture of conventional and synthetic oils. It has high oxidation resistance, predictable characteristics, and consistent structural stability compared to conventional oils.
For engine oil to serve its purpose effectively, it must have the following properties:
Oil Viscosity
Oil viscosity is the internal friction within an oil that resists its flow. It measures the oil's resistance to flow and is the most important factor in lubrication. Engine oils are rated by their viscosity using the SAE (Society of Automotive Engineers) system, such as 5W-30. The "5W" indicates the oil's viscosity at low temperatures (winter), while "30" indicates its viscosity at high temperatures.
Thermal Stability
Thermal stability refers to the oil's ability to withstand high temperatures without breaking down. Oil with good thermal stability resists degradation even at very high temperatures, preventing sludge formation and keeping the engine clean.
Lubrication
Lubrication is the ability of oils to reduce friction between moving parts. Applying oil in the vehicle engine minimizes wear and tear on engine parts, prolonging their life and improving fuel efficiency.
Oxidation Resistance
Oxidation resistance is a property that describes how well the oil resists reacting with oxygen. Oils that resist oxidation are less likely to form harmful deposits and sludge, which can clog the engine and reduce efficiency.
Cleaning Properties
A good oil should have detergency properties that prevent the buildup of contaminants like dirt and soot by suspending and cleaning them away. This helps avoid deposits on engine parts and keeps the oil clean for longer.
Corrosion Resistance
Engine oils contain additives that neutralize acids and protect against rust and corrosion. This prevents engine parts from corroding, especially in parts exposed to moisture or combustion by-products.
There are two basic methods for lubricating engines:
Bath or Splash Lubrication
An engine that utilises splash lubrication does not require an oil pump or oil filter. The transmission gearbox and differential unit employ the pure splash method.
Force-Feed Lubrication
Force-feed lubrication uses an oil pump to force the oil through to lubricate parts, normally through the engine crankshaft and camshaft. All modern motor vehicles use this lubrication method.
Checking the engine oil level is the process of inspecting the amount of oil in a vehicle's engine to ensure it is within the proper range for ideal performance and protection of the engine.
Using the Dipstick
A dipstick is a metal or plastic rod inserted into the engine oil sump to check the oil level.
Procedures for Checking Engine Oil Level
- Turn off the engine: Allow the engine to cool for a few minutes so the oil can settle in the oil pan for an accurate reading.
- Locate the dipstick: In most vehicles, the dipstick has a brightly coloured handle (orange or yellow) for easy access under the hood.
- Remove the dipstick: Pull the dipstick out of the tube and wipe it clean with a towel or cloth.
- Reinsert the dipstick: Insert the dipstick fully back into the tube, then pull it out again to check the oil level.
- Read the oil level: The dipstick has two marks labelled "low" and "full."
- If the reading is between these marks: This is the optimal range.
- If the reading is below the low mark: The oil is low and you need to add more oil.
- If the reading is at or near the full mark: The oil level is adequate.
Regular oil changes are essential because:
- Over time, engine oil breaks down and loses its effectiveness
- Contaminants accumulate in the oil
- Old oil can form sludge that blocks oil passages
- Fresh oil ensures proper lubrication, cooling, and protection of engine parts
Tools, Equipment and Materials Required
- Draining pan
- Socket wrench set
- Oil filter wrench
- New engine oil (correct grade)
- New oil filter (if required)
- Funnel
- Cotton rags
- Wheel stoppers
- Owner's manual
Steps for Changing Engine Oil
- Ensure the motor vehicle is on a flat surface and the engine is switched off.
- Select tools and materials required.
- Insert wheel stoppers underneath the wheels of the vehicle.
- Open the motor vehicle bonnet.
- Ensure the engine is cool before starting.
- Cover the working part of the motor vehicle body to protect it from oil spills.
- Locate the oil drain plug and position the draining pan beneath it.
- Remove the oil drain plug and allow the old oil to drain completely into the pan.
- Inspect the drain plug and washer for damage; replace if necessary.
- Reinstall the drain plug and tighten securely.
- Locate and remove the old oil filter using an oil filter wrench.
- Lubricate the rubber gasket of the new oil filter with a small amount of fresh oil.
- Fill the new oil filter with clean engine oil before installing.
- Install the new oil filter by hand, tightening according to manufacturer's specifications.
- Check the engine oil level using the dipstick.
- Add fresh engine oil through the oil filler cap until the level reaches the proper mark on the dipstick.
- Run the engine for a few minutes to circulate the new oil.
- Switch off the engine and wait a minute for the oil to settle.
- Recheck the oil level and top up if necessary.
- Inspect for any oil leaks around the drain plug and filter.
- Remove the draining pan and clean any spills.
- Close the vehicle bonnet and remove wheel stoppers.
- Dispose of the old oil and filter properly at designated collection points.
- Clean tools and working environment, and store tools as per workshop regulations.
In Tanzania, a motorcycle rider in Dar es Salaam or Mwanza would need to change their motorcycle's engine oil regularly to keep the engine running well, especially on dusty roads. For example, a Bajaj Boxer motorcycle used for commercial bodaboda transport in Arusha requires an oil change every 2,000 to 3,000 kilometers to prevent engine wear and extend the motorcycle's life, saving costly repairs that could cost over TSh 200,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools, appropriate oil type and equipment
- Check engine 88
Tathmini ya matokeo
Engine maintenance performed manufactures guideline Principles: The student should explain the principles of Changing engine oil Theories: The explain: - Importance of changing engine oil Circumstantial knowledge Detailed knowledge about:
- Safety precaution while.
- Safe handling of tools and equipment Proper waste disposal procedures
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of: Change engine oil
Method used: The student should explain how to:
- Motorcycle (with complete engine)
- Tool kit
- engine oil
- Fuel pressure gauge
- container for used oil
- Funnel
- Gloves
- Overall Safety boots
- Safety clear glasses
- Manufacturer’s service manual
- Oil can
Swali
Which of the following is NOT a function of engine oil in a motor vehicle engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado