Mada za sehemu hiiPerforming suspension system serviceMada 2
- Servicing front suspension
- Servicing rear suspension
The rear suspension of a motorcycle supports the rider and load, absorbs road shocks, and keeps the rear wheel in proper contact with the road. Servicing the rear suspension means checking, cleaning, lubricating, and replacing worn parts so the system works safely and smoothly.
Regular servicing:
- Prevents excessive wear on tyres, bearings, and swingarm bushings
- Maintains rider comfort and handling stability
- Reduces the risk of accidents caused by suspension failure
- Extends the life of the motorcycle
- Keeps the swingarm pivot tight: a worn pivot lets the rear wheel move from side to side, which makes the motorcycle weave and wears the chain and sprockets quickly
- Finds weak springs early: a spring that has lost its tension lets the rear sag and hit its stops, so the load is carried badly and the ride becomes unsafe
Before starting, gather these items:
- Motorcycle with rear suspension system
- Suspension tool kit
- Grease gun
- Wheel remover trolley
- Motor-cycle lift or stand
- Bearing remover kit
- Protective gloves
- Torque wrench, spanners and a C-spanner (hook spanner) for the spring adjuster
- Steel rule or tape measure
Always wear gloves to protect your hands from grease, sharp edges, and dirty parts.
Using the Service Manual
Before starting, find the rear suspension section of the service manual for the exact model. It gives the correct order of work, the tightening torque for the axle nut, the shock absorber mounting bolts and the swingarm pivot nut, the service limits (such as the minimum free length of the spring and the swingarm play allowed), and the type of grease to use. Keep the manual open at the bench and follow its figures; do not guess.
Step 1: Prepare the Motorcycle
- Park the motorcycle on a flat, stable surface.
- Use a motor-cycle lift or stand to raise the rear wheel slightly off the ground so it can spin freely.
- Ensure the motorcycle is stable and cannot fall.
- Before loosening any shock absorber bolt, support the swingarm or rear wheel so that it cannot drop when the shock absorber is released. On a motorcycle with two rear shock absorbers, remove one at a time.
Step 2: Remove the Rear Wheel
- Disconnect the rear brake rod or cable where the manual says so, remove the split pin if one is fitted, and loosen the rear axle nut using the correct socket or spanner from the tool kit.
- Slide the wheel remover trolley under the rear wheel for support.
- Carefully remove the axle, lift the chain off the sprocket and take the rear wheel off the swingarm.
- Set the wheel aside in a safe place.
Step 3: Inspect the Rear Suspension Components
With the wheel removed, you can clearly see the suspension parts. Check each of the following:
- Spring or shock absorber: Look for cracks, oil leaks, or bending. A shock absorber that leaks oil is damaged and must be replaced.
- Swingarm: Check for bends and cracks. Grip the ends of the swingarm and try to move it from side to side: there should be no side play at the pivot, and it should swing up and down smoothly.
- Bushing and bearings: Feel for roughness or looseness when you move the swingarm. If there is play, the bearings or bushes are worn and must be replaced; grease does not cure play.
- Linkage and mounting bolts: Make sure all bolts are tight and not rusted or broken, and check the rubber bushes at the top and bottom shock absorber mounts for cracks and wear.
Step 4: Clean the Components
- Use a clean cloth to wipe away dirt, dust, and old grease from all suspension parts.
- Use a wire brush to remove rust from metal surfaces if necessary.
- Do not use water near bearings — moisture causes rust.
Step 5: Apply Grease
- Using the grease gun, apply fresh grease to:
- The swingarm pivot bearings
- The linkage points and bushes
- Any grease nipples (zerk fittings) found on the swingarm pivot or linkage
- Pump until a little fresh grease appears at the edge of the bearing or bush, then wipe off the surplus, because extra grease collects dirt. Keep grease away from the tyre, the brake drum or disc and the brake linings.
Step 6: Check and Replace Worn Parts
- If any bearing feels rough or has play, use the bearing remover kit to press out the old bearing.
- Fit a new bearing, making sure it sits squarely in its housing.
- Replace any cracked or severely worn components before reassembly.
- On a motorcycle with two rear shock absorbers, replace them as a pair so that both sides behave the same.
Step 7: Reassemble the Rear Wheel
- Place the rear wheel back onto the swingarm.
- Insert the axle, refit the chain and reconnect the rear brake.
- Adjust the chain slack and check that the wheel is aligned, using the marks on both sides of the swingarm.
- Tighten the axle nut to the torque given in the service manual and fit a new split pin where one is used.
- Make sure the wheel spins freely without wobble.
- Lower the motorcycle back to the ground.
Step 8: Final Check
- Spin the rear wheel by hand — it should rotate smoothly.
- Push down on the rear of the motorcycle to test the suspension action — it should compress and rebound smoothly without sticking.
- Check that all bolts and nuts are tightened to the correct torque, and that the rear brake works properly before the motorcycle is ridden.
A spring that has lost its tension (become weak) lets the rear of the motorcycle sit low and hit its stops on bumps.
Coil springs
- With the motorcycle on its wheels, look at it from behind and from the side. It should sit level, and on a motorcycle with two shock absorbers both springs should look the same length.
- Push down hard on the seat and release. The rear should go down smoothly and come back up once, without bouncing several times and without hitting its stops.
- Check each coil for cracks, rust pitting and coils that touch each other.
- Where the manual allows the spring to be removed, measure its free length (its length when removed and unloaded) with a steel rule and compare it with the service limit in the manual. A spring shorter than the limit is weak and must be replaced. Where a spring tester is available, the manual also gives the load the spring should carry at a stated length.
Never dismantle a shock absorber without the proper spring compressor: the spring is held under strong pressure and can fly out and injure you. Never open, heat or puncture a gas-filled shock absorber.
Leaf springs are fitted to some three-wheeled motorcycles and cargo tricycles. Check them for cracked or broken leaves, leaves that have shifted out of line, and a spring that has gone flat or sits lower on one side (measure the height on both sides). Check that the centre bolt, U-bolts and clips are tight and that the shackle bushes are not worn. Replace a broken or flattened spring; do not weld a leaf.
- Spring preload: most rear shock absorbers have a stepped or threaded adjuster collar at the end of the spring. Turn it with the C-spanner to a higher setting for heavy loads or a passenger, and to a lower setting for a light rider. Set both shock absorbers to the same position.
- Chain and wheel alignment: after any work that moves the rear wheel, adjust the chain slack to the figure in the manual and set the adjusters on both sides to the same mark.
- Fasteners: tighten the shock absorber mounting bolts, the swingarm pivot nut and the axle nut to the torque given in the manual.
A motorcycle is brought to a workshop with a sagging rear end and oil stains on the shock absorber body.
- Diagnosis: The shock absorber is leaking oil, which means it has lost its damping ability.
- Action: A leaking sealed shock absorber of this kind is not repaired in the workshop, so it must be replaced with a new one of the same type. On a motorcycle with two rear shock absorbers, both are replaced together.
- Service: After replacing the shock absorber, the mechanic checks the swingarm pivot bearings, cleans them, and applies fresh grease.
- Result: The rear suspension now works correctly, and the motorcycle rides level and smoothly again.
- Wipe grease and dirt off every tool and return it to the tool board or toolbox. Wipe the grease gun and store it where it cannot leak onto the floor.
- Lower the lift, put the stands and the wheel trolley back in their places, and sweep the floor. Cover spilled oil or grease with sawdust or sand and sweep it up, because it is a slip hazard.
- Put old bearings, bolts and springs in the scrap metal bin.
- Old shock absorbers contain oil and sometimes gas under pressure. Do not burn, puncture or dump them; hand them over with the workshop's scrap metal or waste oil collection.
- Put greasy rags and used gloves in a covered metal bin for oily waste. Never pour oil or cleaning solvent onto the ground or into a drain.
- Wash your hands with soap when you finish.
- Always support the motorcycle safely before working underneath it.
- Never use water to clean bearings — always use a dry cloth or brush.
- Grease fittings (zerk nipples) should be greased regularly to prevent wear.
- Replace damaged shock absorbers rather than trying to repair them.
- After reassembly, always test the suspension movement before riding.
- Forgetting to check the swingarm pivot bearings
- Over-greasing, which causes dirt to build up
- Not tightening the axle nut properly, which can make the wheel loose
- Riding the motorcycle before doing a final check
In Tanzania, motorcycle taxis (bodaboda) carry heavy loads and passengers daily. A bodaboda rider in Arusha who regularly services the rear suspension of his motorcycle — greasing the swingarm bearings and checking the shock absorbers — will experience a smoother ride, fewer tyre wear issues, and reduced risk of breakdowns on rough roads. This saves money on repairs and keeps the rider and passengers safe while earning a living.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools and equipment
- Check rear suspension system components
- Adjust rear suspension system components
- Repair rear suspension system components
- Observe safety precautions
- Clean tools, equipment and working place
- Store and keep tools and equipment
- Dispose wastes
Tathmini ya matokeo
Rear suspension serviced as per manufactures guideline.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Servicing rear suspension
- Test coil and leaf spring suspension tension
Principles: The student should explain principles of:
- Servicing rear suspension system components
Theories: The student should explain: -
- Importance of Servicing rear suspension
- Importance of servicing swing arm
- Importance of testing coil spring tension
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while Servicing rear suspension
- Safe handling of tools and equipment
- Waste disposal methods
Swali
What is the main job of a motorcycle's rear suspension?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado