Mada za sehemu hiiAdjusting valve clearanceMada 2
- Performing valve overlap adjustment method
- Performing one to one valve adjustment method
Valve overlap adjustment is a method used to set the correct gap between the valve stem and the rocker arm (or camshaft lobe) so that the engine's valves open and close at the right time. This gap is called valve clearance, and it must be checked and adjusted during routine engine maintenance to keep the engine running smoothly and efficiently.
An engine valve is a crucial component that controls the flow of gases in and out of the combustion chamber. There are two types of valves in every cylinder:
- Intake valve – allows the air-fuel mixture to enter the combustion chamber
- Exhaust valve – allows the burnt gases to exit the combustion chamber after combustion
The camshaft controls these valves, opening and closing them at precise intervals determined by the engine's timing. Proper operation of these valves is essential for engine performance, fuel efficiency, and emissions control.
Valve clearance (also called valve lash) is the small gap between the engine's valve stem and its rocker arm or camshaft lobe. This gap ensures that the valves close fully and open at the correct times during the engine's cycle.
If the clearance is too small, the valve may not close completely, causing loss of compression and potential engine damage from overheating. If the clearance is too large, the valve opens late and closes early, reducing engine power and causing noisy operation.
The exact clearance specification varies by engine type and is given in the service manual, usually measured in millimetres (e.g., 0.25 mm for intake valves and 0.30 mm for exhaust valves in some engines).
Valve overlap refers to the period when both the intake and exhaust valves are open simultaneously during the engine's cycle. This happens at the end of the exhaust stroke and the beginning of the intake stroke.
During valve overlap adjustment, we set the valve clearance while the cylinder is at Top Dead Centre (TDC) on its compression stroke. At this point, both valves should be closed, and the rocker arms should have some free play. This allows the mechanic to measure and adjust the gap accurately.
Adjusting valve clearance is important for several reasons:
- Optimal engine performance – proper clearance ensures valves open and close at the correct times, maintaining full engine power
- Fuel efficiency – correct clearance helps the engine burn fuel more completely, saving fuel
- Engine longevity – prevents excessive wear on valve train components like the camshaft and rocker arms
- Reduced noise and vibration – properly adjusted valves operate quietly and smoothly
Before starting, gather these tools:
- Feeler gauge set
- Wrench set
- Socket set and ratchet
- Screwdriver (flathead or Phillips)
- Torque wrench
- Engine service manual (for specifications)
- Safety gear: gloves, overall, safety glasses, clean rags
Follow these steps carefully:
Step 1: Prepare the Vehicle
Park the vehicle on a flat surface. Turn off the engine and let it cool completely to prevent burns. Engage the parking brake and place wheel chocks behind the wheels.
Step 2: Access the Valve Cover
Open the hood and locate the valve cover. Remove any components blocking access, such as the air intake duct or ignition coils.
Step 3: Remove the Valve Cover
Use a socket and ratchet to remove the bolts securing the valve cover. Lift it off to expose the rocker arms, camshaft, and valves. Keep all hardware in a clean place.
Step 4: Locate Top Dead Centre (TDC)
Rotate the engine's crankshaft using a wrench on the crankshaft pulley bolt until the cylinder to be adjusted is at TDC on its compression stroke. At TDC, both intake and exhaust valves should be closed, and the rocker arms should have some free play.
Step 5: Check the Valve Clearance
Insert the appropriate feeler gauge between the valve stem and the rocker arm (or camshaft lobe). The gauge should slide in with a slight drag. Compare the reading with the specifications in the service manual.
Step 6: Adjust the Clearance
For rocker arms with a screw and locknut:
- Loosen the locknut with a wrench while holding the adjustment screw with a screwdriver
- Turn the adjustment screw to set the clearance: clockwise to decrease, counterclockwise to increase
- Once the correct clearance is achieved, tighten the locknut while holding the adjustment screw in place
For overhead cam engines with shims, remove the camshaft to access and change the shims. Use a micrometer to measure the existing shim thickness and select the correct replacement.
Step 7: Recheck the Clearance
After adjusting, recheck the clearance with the feeler gauge to ensure it is within the specified range. Adjust again if necessary.
Step 8: Repeat for All Valves
Rotate the crankshaft to bring each cylinder to TDC on its compression stroke. Repeat the checking and adjustment process for all intake and exhaust valves.
Step 9: Reinstall the Valve Cover
Clean the valve cover mating surfaces and replace the gasket if needed. Reinstall the valve cover and secure it with bolts. Tighten to the manufacturer's torque specifications using a torque wrench.
Step 10: Reassemble and Test
Reattach any components removed to access the valve cover. Start the engine and listen for unusual noises. Allow it to reach operating temperature and check that it runs smoothly.
Step 11: Final Inspection
Check for oil leaks around the valve cover and ensure all components are properly secured.
Suppose a motorcycle engine requires intake valve clearance of 0.25 mm and exhaust valve clearance of 0.30 mm. A student checks the intake valve of cylinder 1 using a 0.25 mm feeler gauge and finds it drags slightly. When checking the exhaust valve with a 0.30 mm feeler gauge, the gauge slides in too easily (clearance is too large).
To fix the exhaust valve:
- Locate the adjustment screw and locknut on the rocker arm
- Hold the adjustment screw with a screwdriver and loosen the locknut with a wrench
- Turn the adjustment screw counterclockwise (to increase clearance) until the 0.30 mm gauge slides in with slight drag
- While holding the adjustment screw in position, tighten the locknut securely
- Recheck with the feeler gauge to confirm the adjustment is correct
The same process is repeated for all other cylinders following the engine's firing order.
In Tanzania, small business owners who operate motorcycles for transport (bodaboda) or small trucks for market deliveries need to perform valve clearance adjustments during regular service to keep their vehicles running efficiently. For example, a bodaboda rider in Dar es Salaam can save money on fuel by ensuring proper valve clearance, which helps the engine burn fuel completely and reduces the amount of petrol spent on daily routes between Buguruni and Kariakoo market.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Select tools and equipment.
- Perform valve overlap adjustment
- Observe safety precautions.
- Clean tools, equipment and work place.
- Store tools and equipment.
Tathmini ya matokeo
Adjusted valve clearance conforms to manufacturer’s specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to perform valve adjustment:
- Valves overlap adjustment method.
Principles: Students should explain the principles of construction of valve train mechanism.
Theories: Students should explain:
- Effects of incorrect valve clearance on engine.
- Piston pairs
- Advantage of overhead camshaft engines compared to side cam shaft engines.
- Reasons for some engines which need no valve clearance adjustment.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while adjusting valve clearance.
- Safe handling of work tools and equipment.
- Waste disposal.
Swali
What is valve clearance in an internal combustion engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado