Mada za sehemu hiiPerforming crankshaft measurementsMada 3
- Checking bearing oil clearance
- Checking for crankshaft straightness
- Checking crankshaft journals
Bearing oil clearance is the small gap between the crankshaft journal (the polished cylindrical surface that rotates in the bearing) and the inner surface of the bearing. This gap allows engine oil to form a thin film that separates the metal surfaces, preventing direct contact and reducing friction during engine operation.
When you turn the crankshaft in a running engine, the oil pump sends oil under pressure into this space. The rotating journal "wipes" the oil around, creating a cushion that keeps the metal parts apart. Without this oil film, the bearing would quickly overheat and seize, causing catastrophic engine failure.
The correct oil clearance is essential for three main reasons:
- Prevents metal-to-metal contact — The oil film acts as a protective barrier between the crankshaft and bearing
- Maintains oil pressure — Proper clearance ensures the oil pump can maintain adequate pressure throughout the engine
- Ensures cooling — The oil film carries away heat generated by friction between moving parts
If the clearance is too small, the oil cannot flow properly, leading to insufficient lubrication and overheating. If the clearance is too large, oil pressure drops, causing insufficient lubrication and rapid bearing wear.
Insufficient (Too Small) Clearance
- Excessive friction between bearing and journal
- Overheating of the bearing surface
- Bearing seizure (complete failure)
- Metal scoring on journal surfaces
Excessive (Too Large) Clearance
- Low oil pressure throughout the engine
- Metallic knocking or tapping noises
- Premature bearing wear and failure
- Oil consumption and oil loss
- Inside micrometer
- Outside micrometer (external micrometer)
- Feeler gauge or plastigauge (plastic gauge)
- Service manual (manufacturer specifications)
- Clean rags and solvent
- Torque wrench
- Dial bore gauge (optional)
This is the most common method used in Tanzanian workshops because it gives a direct reading of the actual clearance.
Procedure
-
Clean thoroughly — Remove all oil, dirt, and debris from the crankshaft journal and bearing surfaces. Any contamination will give false readings.
-
Place the gauge — Cut a narrow strip of plastigauge (or use feeler gauge) and lay it carefully across the centre of the crankshaft journal, parallel to the journal axis.
-
Install the bearing cap — Place the bearing cap in position and tighten the bolts to the specified torque (check your service manual for the correct value). Do not rotate the crankshaft while the gauge is in place.
-
Remove and measure — Carefully remove the bearing cap without disturbing the flattened gauge. The plastigauge will be compressed to a width that corresponds to the oil clearance.
-
Compare — Measure the width of the flattened gauge using the scale printed on the plastigauge packet. Compare this reading with the manufacturer's specification.
Example: If the manufacturer's specification states that bearing oil clearance should be between 0.02 mm and 0.05 mm, and your plastigauge reads 0.04 mm after measurement, the clearance is acceptable and within limits.
This method calculates clearance by measuring each component separately.
Procedure
-
Clean the components — Thoroughly clean the crankshaft journal and bearing as before.
-
Measure the journal diameter — Use an outside micrometer to measure the crankshaft journal diameter at multiple points (front, middle, and rear of the journal). Take the average reading.
-
Measure the bearing internal diameter — Use a dial bore gauge or inside micrometer to measure the internal diameter of the bearing.
-
Calculate the clearance — Subtract the journal diameter from the bearing internal diameter:
Oil Clearance=Bearing ID−Journal OD
Worked Example:
- Bearing internal diameter measured: 52.00 mm
- Crankshaft journal diameter measured: 51.96 mm
- Oil clearance = 52.00 − 51.96 = 0.04 mm
Compare this 0.04 mm with the manufacturer's specification (e.g., 0.02–0.05 mm). Since 0.04 mm falls within this range, the clearance is acceptable.
| Condition | Measured Clearance | Action Required |
|---|---|---|
| Within specification | 0.02 – 0.05 mm | No action needed; proceed with assembly |
| Too small | Less than 0.02 mm | Select a new bearing with smaller internal diameter, or grind the crankshaft journal to a smaller undersize |
| Too large | More than 0.05 mm | Select a new bearing with larger internal diameter, or regrind the crankshaft journal to the next oversize |
- Always refer to the service manual for manufacturer specifications — different engines have different clearance requirements
- Take measurements at multiple points around each journal to check for out-of-round conditions
- Ensure all components are completely clean before measurement
- Never reuse plastigauge; use a fresh strip for each measurement
- Record all measurements for future reference
In Tanzania, a mechanic at a local garage in Arusha or Mwanza checking bearing oil clearance during an engine overhaul can determine whether the engine needs expensive new bearings or crankshaft grinding. For example, if clearance is too large (0.08 mm instead of the specified 0.03 mm), the mechanic knows the engine will develop low oil pressure and knock loudly after reassembly — problems that would cost the vehicle owner significantly more to repair later if not caught early.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Select tools and equipment
- Check bearing oil clearance.
- Observe safety precautions.
- Clean tools, equipment, parts and work place.
- Store tools and equipment.
Tathmini ya matokeo
Bearing oil clearance checked as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Check bearing oil clearance
Principles: Students should explain the principle of:
- Tightening main bearing caps.
Theories: Students should explain:
- Procedures for Checking bearing oil clearance
- Importance of Checking bearing oil clearance
- Sizes of bearings.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing crankshaft measurements.
- Safe handling of work tools, equipment and parts.
- Waste disposal.
Swali
What is meant by bearing oil clearance in an engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado