Mada za sehemu hiiConducting preventive maintenance of work toolsMada 5
- Maintaining measuring tools
- Maintaining general hand tools
- Maintaining engine and engine accessory tools
- Maintaining tire, wheel, hub, and brake tools
- Maintaining electrical circuit and light system
Proper maintenance of tire, wheel, hub and brake tools keeps them safe to use, helps them last longer and prevents costly breakdowns. In this study note you will learn what each tool does, how to look after it, and the simple steps you can follow in the workshop.
- Wear the personal protective equipment (PPE) listed for this activity: gloves, safety boots, safety clear glasses and an overall.
- Before you start, make sure the air compressor is switched off and the power supply is disconnected when required.
- Keep the work area clean; remove oil spills or loose objects that could cause you to slip.
- Always refer to the service manual and the preventive‑maintenance schedule for the exact intervals and specifications for each tool.
- Basic hand tools (spanners, screwdrivers, pliers)
- Oil can (light machine oil)
- Air compressor with tyre‑inflator attachment
- Tyre pressure gauge
- Wire brush, clean cloths, cotton waste
- Service manual for the equipment you are working on
- Preventive‑maintenance schedule (chart)
1. Tire tools (inflation and inspection)
- Inspect the tyre – Look for cuts, cracks, bulges or embedded objects on the tread and sidewall.
- Check the valve – Make sure the valve stem is not damaged and the cap is present.
- Measure pressure – Use a tyre‑pressure gauge; compare the reading with the value given in the service manual (often 1.5–2.2 bar for tractor tyres).
- Inflate or deflate – Connect the air compressor, inflate to the correct pressure, or release air if over‑inflated.
- Clean the tyre – Wipe away mud and oil with a clean cloth; a wire brush can remove stubborn dirt from the tread.
- Record the work – Mark the date and pressure on the maintenance schedule.
2. Wheel tools (rim and spoke care)
- Remove the wheel – Use a suitable spanner to loosen the nuts, then lift the wheel off.
- Clean the rim – Scrub the rim with a wire brush to remove rust, dirt and old lubricant. Wipe with a dry cloth.
- Check for damage – Look for cracks, dents or bent spokes. If spokes are loose, tighten them with a spoke‑wrench.
- Lubricate the rim – Apply a thin film of light oil to the rim surface to prevent rust (do not over‑oil).
- Re‑fit the wheel – Tighten the nuts to the torque specified in the manual.
3. Hub tools (bearing and axle)
- Clean the hub – Use cotton waste to wipe away old oil and dirt.
- Inspect the bearing – Check for wear, pitting or missing rollers. If damaged, replace the bearing.
- Apply oil – Use the oil can to put a few drops of machine oil on the bearing surface and on the axle where it contacts the hub.
- Check for play – Gently wiggle the hub; any noticeable movement indicates that the bearing is worn and must be adjusted or replaced.
- Re‑assemble – Refit any covers or seals and make sure everything is tight.
4. Brake tools (shoes, pads, cables)
- Inspect brake shoes/pads – Look for wear, cracking or uneven thickness. Replace if the material is less than the minimum specified in the manual.
- Clean the brake drum or disc – Remove dust and oil with a clean cloth; use a wire brush only on metal parts.
- Lubricate moving parts – Apply a drop of oil to the brake‑cable housing, the pivot points of the brake arm, and any adjusting screws.
- Adjust the brake – Use the adjusting nut to set the correct clearance (typically 1–2 mm for disc brakes, a slight drag for drum brakes).
- Test the brake – Spin the wheel and press the brake lever; the wheel should stop quickly and smoothly.
- After use, wipe all hand tools with a dry cloth to remove oil and moisture.
- Lightly oil pivots, hinges and any moving parts to keep them working smoothly.
- Store tools in a clean, dry place; hang spanners on a pegboard or keep screwdrivers in a rack.
- Follow the preventive‑maintenance schedule to inspect your tools regularly.
A farmer’s trailer tyre was found to be at 1.0 bar (too low). According to the service manual, the correct pressure is 1.8 bar.
- The student put on gloves, safety boots and safety glasses.
- Using the tyre‑pressure gauge, the reading was recorded.
- The air compressor was connected, the tyre inflated to 1.8 bar and the valve cap was replaced.
- The wheel rim was cleaned with a wire brush and a thin coat of oil was applied to stop rust.
- The hub bearing was oiled and the brake shoes were inspected – they were still within limits, so only a light oil film was applied to the brake‑cable pivot.
The trailer was now ready for safe transport of produce to the market.
- Always follow the order given in the preventive‑maintenance schedule.
- Never over‑inflate a tyre; check the recommended pressure for the load you will carry.
- Keep oil away from brake pads – oil contaminates the friction material and reduces braking power.
- If you are unsure about any part, ask your teacher or refer to the service manual.
In Tanzania, small‑scale traders often use motorcycles or small trucks to carry produce to market. Keeping the tyre, wheel, hub and brake tools properly serviced prevents breakdowns on rural roads, ensures safety when transporting bags of maize or beans, and saves money that would otherwise be spent on expensive repairs or replacements.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Use service manual
- Select tools and equipment
- Interpret service manuals for different tools
- Select tools, equipment and materials
- Check functionality of tire,wheel,h ub and brake tools
- Identify fault tools
- Perform greasing
- Observe safety
- Clean tools, equipment and work place
- Store tools
Tathmini ya matokeo
Tire,wheel,hub and brake tools maintained as per required standard.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Service tire,wheel,hub and brake tools
Principles: Students should explain the principles of:
- Preventing tire,wheel,hub and brake tools
- Storing tire,wheel,hub and brake tools
Theories: Students should explain:-
- Function of different types of tire,wheel,hub and brake tools Circumstantial
Detailed knowledge about:
- Safety precautions while handling basic tools
- Safe handling of work tools and equipment
- Waste disposal procedures
Swali
Which item of Personal Protective Equipment (PPE) is NOT listed as required when maintaining tire, wheel, hub and brake tools?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado