Mada za sehemu hiiPerforming cuttingMada 3
- Performing straight sawing
- Performing angular sawing
- Performing chiselling
Angular sawing is the process of cutting materials at specific angles other than a straight 90° cut. It is commonly used in agro-mechanics for shaping metal parts in farm equipment repair and fabrication.
Angular sawing refers to making cuts in materials such as metal, wood, or plastic at specific angles. These angles can be:
- Acute angle — less than 90° (e.g., 45°)
- Right angle — exactly 90°
- Obtuse angle — greater than 90° (e.g., 135°)
The saw blade is adjusted to the desired angle before cutting. This technique is essential when joining pieces at corners or creating beveled edges.
Angle Adjustment
To perform angular sawing, you must adjust your cutting tool to the required angle. Common angles used in workshop practice include 45°, 90°, 135°, and 180°. A protractor or angle gauge is used to measure and set the correct angle on the workpiece.
Precision
Angular cuts must be accurate to ensure proper fit between joined parts. Even small errors can cause gaps or misalignment in assembled equipment.
Safety
Safety precautions are crucial when performing angular sawing. Always wear appropriate PPE and handle tools carefully to prevent injuries.
| Tools/Equipment | Materials | Safety Gears |
|---|---|---|
| Work bench | Cotton waste | Safety boots |
| Angle grinder | Workpiece (material to be cut) | Overall |
| Bench vice | Drill bits | Leather gloves |
| Protractor | Safety goggles |
A hacksaw with a 12-inch (300mm) bi-metal blade with 24 teeth per inch (TPI) is commonly used for angular cutting on metal workpieces.
- Wear PPE — Put on safety boots, overall, leather gloves, and safety goggles before starting.
- Select the workpiece — Choose the material to be cut (e.g., a 10 mm flat bar).
- Mark the angle — Use a protractor and scribing tool to mark the required angle (e.g., 45°) on the workpiece.
- Secure the workpiece — Clamp the workpiece firmly in a bench vice to prevent movement during cutting.
- Set the angle — If using an adjustable hacksaw or angle grinder, set the correct angle.
- Perform the cut — Hold the hacksaw at the marked angle and make steady, even strokes along the cut line.
- Support the piece — When the blade nearly cuts through, support the piece with your hand to prevent it from dropping.
- Inspect the cut — Check that the cut matches the required angle and is clean.
- Clean up — Remove chips and debris using a brush, not your bare hands.
A student is given a 10 mm flat bar × 200 mm long and must cut it into six lengths at a 45° angle. The student:
- Marks six points along the bar at 45° angles using a protractor
- Secures the bar in a vice
- Cuts along each marked line with a hacksaw
- Checks each piece with a protractor to ensure accuracy
This skill is used when fabricating brackets or mounting plates for agricultural machinery that require angled joints.
- Do not continue a cut with a new blade in the same slot created by a dull blade — the new blade will stick and be ruined. Rotate the workpiece and cut from the other side, or start a new cut next to the first one.
- Support the piece being cut off to prevent it from falling and causing injury.
- Release blade tension before storing the hacksaw to prevent the frame from losing its spring.
- Never test blade sharpness by running your finger across the teeth — you will get a cut.
- Store the hacksaw so you do not accidentally grasp the teeth when picking it up.
- Do not wipe chips away with your hand — the burr on cut surfaces is sharp and can cause serious cuts.
- Cut on the correct side of the vice — right-handed persons should cut on the right-hand side of the vice to avoid injury if the blade breaks.
In Tanzania, a farmer or workshop technician repairing a hand hoe or irrigation pump may need to cut metal brackets at 45° angles to create strong, properly fitting joints. For example, when fabricating a replacement bracket for a water pump using a flat bar, knowing how to perform angular sawing ensures the parts fit correctly, reducing leakage and extending the equipment's life. This skill is valuable for small-scale metalwork businesses in local markets.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools and equipment.
- Take measurements.
- Cut work piece.
- Check for accuracy.
- Observe safety precautions
- Clean tools, work piece and work place.
- Store tools, equipment and workplace.
Tathmini ya matokeo
Angular sawing performed as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to cut work piece in different sizes.
Principles: Students should explain the principles of:
- Taking measurements.
- Marking work piece.
- Cutting process.
Theories: Students should explain:
- Different types of materials and their properties.
- Application of different materials.
- Uses of cutting tools and equipment.
- Use of measuring tools.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing cutting process.
- Safe handling of work tools and equipment.
- Waste disposal.
Swali
What is angular sawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado