Mada za sehemu hiiPerforming threadingMada 2
- Carrying out die threading
- Carrying out tapping
Carrying Out Dieing
Dieing is the process of cutting external threads on a cylindrical workpiece (such as a bolt or rod) using a threading die. This is the opposite of tapping, which creates internal threads. Dieing is also called die threading or external thread cutting.
Dieing allows you to:
- Create new bolts or studs with external threads
- Repair damaged threads on existing rods or bolts
- Produce custom-length threaded fasteners for farm equipment repair
- Extend the life of broken bolts by re-threading them
The following tools are required for dieing:
Threading dies and stocks:
- Die — a threaded cutting tool with cutting edges on the inside circumference
- Die stock — the handle that holds the die firmly during cutting
Measuring tools:
- Steel rule, micrometer, vernier caliper, thread gauges
Supporting tools:
- Work bench, centre punch, scriber, wire brush, oil can
Personal Protective Equipment (PPE):
- Safety boots, overalls, leather gloves, safety goggles
Step 1: Preparation
- Ensure the workpiece is clean and free from rust or burrs
- Use a wire brush to clean the rod surface where the thread will be cut
- Select the correct die size for the required thread (e.g., M10, M12)
Step 2: Marking and Starting Point
- Measure and mark the length of thread required on the workpiece using a steel rule
- Use a centre punch to create a small indentation at the starting point to guide the die
Step 3: Lubrication
- Apply cutting oil to the workpiece and die teeth to reduce friction and heat
- This prevents the die from sticking and ensures a clean thread
Step 4: Holding the Die Stock
- Insert the die into the die stock and tighten the fixing screws firmly
- Hold the die stock with both hands, keeping it perpendicular (90°) to the workpiece
Step 5: Starting the Cut
- Position the die squarely on the end of the workpiece
- Apply light downward pressure and turn the die stock slowly clockwise
- Make 2-3 partial rotations, then reverse slightly to break the chips
Step 6: Continuing the Thread
- Apply steady pressure and continue turning the die stock clockwise
- Periodically apply more cutting oil
- After every few turns, turn the die counter-clockwise to clear chips
Step 7: Completing the Thread
- Continue until the required thread length is achieved
- Hold the workpiece firmly to prevent it from rotating with the die
Step 8: Finishing
- Remove the die by turning counter-clockwise
- Clean the newly cut thread with a wire brush
- Wipe with clean cotton waste
- Check the thread quality using a thread gauge
A farmer has a broken M10 bolt on a plough harness. The remaining bolt is 80 mm long but has no thread. You need to cut a 25 mm M10 thread on this bolt using a 25 mm die.
Solution:
- Clean the 80 mm rod end with a wire brush
- Measure 25 mm from the end and mark with a scriber
- Apply cutting oil to the rod
- Insert M10 die into die stock and tighten
- Position die at 90° to the rod, start cutting clockwise
- Apply light pressure, turn 2-3 revolutions, reverse to break chips
- Continue cutting while adding oil every few turns
- Stop when 25 mm of thread is formed
- Remove die, clean thread, and check with M10 thread gauge
- Always wear safety goggles to protect eyes from flying metal chips
- Wear leather gloves when handling rough metal surfaces
- Wear safety boots to protect feet if the workpiece falls
- Wear overalls to protect clothing
- Ensure the workpiece is securely held before starting
- Use cutting oil to prevent overheating
- Keep fingers away from the die teeth while cutting
| Problem | Cause | Solution |
|---|---|---|
| Thread is rough | Dull die or insufficient oil | Apply more oil; use a sharper die |
| Thread is oversize | Die not held perpendicular | Hold die stock at 90° to workpiece |
| Die sticks | Chips not cleared | Reverse direction frequently to clear chips |
| Thread is incomplete | Insufficient pressure | Apply steady downward pressure while turning |
In Tanzanian agro-mechanics workshops, dieing is commonly used to repair broken bolts on farming equipment such as ploughs, seeders, and trailers. When a bolt snaps on a farm implement in Morogoro or Arusha, a farmer can use a die to cut new threads on the remaining metal, saving the cost of buying a new bolt. This skill is valuable for small-scale mechanics and farmers who need to maintain their equipment without waiting for spare parts from Dar es Salaam.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools, equipment and materials.
- Mark work piece.
- Observe safety precautions
- Carry out die threading
- Clean tools, equipment, work piece and work place.
- Store tools, equipment and work piece.
Tathmini ya matokeo
Dieng carried out conform to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- procedures for performing die threading
Principles: Students should explain the principles of:
- Carrying out dieng.
Theories: Students should explain:
- The function of dies.
- Types of dies.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while cutting threads.
- Safe handling of tools, equipment and materials.
- Waste disposal.
Swali
What is dieing in agro-mechanics?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado