Mada za sehemu hiiServicing gear type pumpsMada 2
- Performing adjustment on gear pumps
- Disassembling and assembling gear type pumps
A gear type pump is a positive displacement pump used in agricultural machinery to move fluids such as fuel, lubricating oil, and hydraulic fluid. It works by trapping fluid between the teeth of two interlocking gears — a drive gear and an idler gear — inside a sealed housing. When the gears rotate, fluid is drawn in on one side and pushed out on the other. Gear type pumps are reliable, compact, and capable of delivering a steady flow at high pressure, which makes them ideal for the lubrication and hydraulic systems of tractors, combine harvesters and other farm machinery.
Understanding each part helps you take the pump apart and put it back together correctly:
- Housing (body) — the main casing that holds all internal parts and connects to the machinery's pipework
- Drive gear — the gear connected to the pump shaft, turned by the engine or motor
- Idler gear — the gear that rotates freely in the opposite direction to the drive gear
- Pump shaft — transmits rotational power from the engine to the drive gear
- Bearings — support the shaft and allow smooth rotation
- Seals and gaskets — prevent fluid leakage and keep contaminants out
- Cover plate — seals the housing and is removed during disassembly
- Relief valve — controls maximum pressure by releasing fluid back to the inlet when needed
Farm machinery operators and mechanics disassemble and assemble gear type pumps to:
- Repair worn or damaged gears, bearings, and seals
- Replace leaking gaskets that cause fluid loss
- Clear blockages in the inlet or outlet passages
- Restore pump performance and pressure output
- Perform routine servicing during the agricultural off-season
Always follow these safety rules before handling any pump or tool:
- Shut down the engine or motor and disconnect the power supply
- Lock out and tag out the power switch so the machine cannot be restarted accidentally
- Wear safety boots, safety goggles, gloves, a helmet, and overalls at all times
- Allow the pump to cool if it has been running — hot fluid can cause serious burns
- Drain all fluid from the pump and connected pipelines into a suitable container
- Secure the pump firmly on a bench vice or workbench before removing any fasteners
- Keep the work area clean and free of oil spills to prevent slipping
| Category | Items |
|---|---|
| Hand tools | Tool kit (spanners, screwdrivers, sockets), grease gun, oil can, bench vice |
| Cutting/fitting tools | Hacksaw, tap and dies, hand grinder |
| Lifting equipment | Tripod stand, chain blocks, lifting tools |
| Holding and carrying | Pipe clamp (holding), wheel barrow (moving heavy parts) |
| Power tools | Drill machine |
| Service information | Service manual for the specific pump model |
| Safety gear | Safety boots, goggles, gloves, helmet, overall |
Follow these steps in order, referring to the service manual for torque specifications and special notes on your specific pump model.
Step 1 — Prepare the work area Ensure the work area is clean and well lit and all tools are within reach. Wipe dirt off the outside of the pump and its pipe connections so nothing falls inside when it is opened.
Step 2 — Remove the pump from the machinery Place a drain pan under the pump, disconnect the inlet and outlet pipes and plug the open ends. Unbolt the pump and lift it off the tractor or machine, using the tripod stand and chain blocks if it is too heavy to lift safely by hand. Secure it in a bench vice.
Step 3 — Drain the fluid Pour any fluid remaining inside the pump into a drain pan. Keep the used oil in a closed container for proper disposal; never pour it on the ground or into a drain.
Step 4 — Mark the housing orientation Use a scribe or marker to draw alignment marks across the housing and cover plate. This ensures the pump goes back together in the exact same orientation, which is critical for maintaining proper gear mesh and alignment.
Step 5 — Remove the cover plate Remove the bolts or nuts holding the cover plate to the housing using the appropriate spanner or socket. Tap the cover plate gently with a soft-faced hammer if it is stuck — never strike hard metal parts directly.
Step 6 — Inspect and remove the gears Carefully note the position and direction each gear faces before removing it. Lift out the drive gear and idler gear together with the shaft assembly. Place them on a clean, flat surface in the order they came out.
Step 7 — Remove bearings and seals Press or tap the bearings and shaft out of the housing using a suitable drift or bearing puller. Remove all seals and gaskets, noting which side faces inward and outward.
Step 8 — Inspect all components Check each part for wear, scoring, pitting, chips, or cracks. Measure gear clearances with a feeler gauge and compare them with the values given in the service manual.
Assemble the pump by reversing the disassembly steps, paying careful attention to cleanliness and alignment.
Step 1 — Clean all parts Thoroughly clean every component with clean diesel or solvent. Blow dry with compressed air or wipe with a clean lint-free cloth. Even a small piece of dirt can cause a leak or seizure.
Step 2 — Install new seals and gaskets Press new oil seals into the housing with the lip facing inward toward the fluid chamber. Install new gaskets between all mating surfaces — never reuse old gaskets.
Step 3 — Lubricate before assembly Apply a thin coat of clean lubricating oil to all bearing surfaces, gear teeth, and shaft journals. This prevents dry starting and reduces initial wear.
Step 4 — Install bearings Press the bearings onto the shaft and into the housing bores using a bearing press or a suitable socket and hammer. Ensure they are seated fully and squarely.
Step 5 — Reinstall the gears Place the idler gear into its bearing, then slide the drive gear and shaft assembly through the housing bore and into the drive bearing. Align the gears so their teeth mesh correctly — the teeth should interlock smoothly without forcing.
Step 6 — Replace the cover plate Align the scribe marks on the cover plate with those on the housing. Install the bolts hand-tight first, then tighten them evenly in a criss-cross pattern to the specified torque. Refer to the service manual for the correct torque value.
Step 7 — Reconnect and test Hand-rotate the shaft to check it turns freely. Reinstall the pump on the machine, reconnect the inlet and outlet pipes and refill the system with the correct fluid. Run it at low speed and check for leaks, unusual noise and normal pressure.
A maize farmer in Morogoro notices his tractor's hydraulic steering feels heavy and slow. He suspects the gear pump on the power steering circuit is faulty. He removes the pump and finds the cover plate gasket is cracked and both gear bearings show play when wiggled by hand.
Disassembly steps taken:
- Secured the pump in a bench vice
- Drained the hydraulic fluid
- Scribed alignment marks on the housing and cover
- Removed the cover plate bolts and cover plate
- Lifted out the drive gear, idler gear, and shaft
- Pressed out the worn bearings and removed the cracked gasket
Assembly steps taken:
- Cleaned all parts with diesel
- Pressed in new bearings and installed a new cover gasket
- Lubricated all surfaces with clean hydraulic oil
- Reinstalled gears, aligned using scribe marks
- Tightened cover bolts evenly to specification
- Refilled with hydraulic fluid and tested — steering felt light and responsive again
- Wipe all tools clean and return them to the tool kit; store the grease gun and oil can upright in their places
- Clean the workbench and floor; soak up spilled oil or grease with sawdust or sand and sweep it up
- Put old packing, gaskets, seals and oily rags in a covered waste bin
- Collect used oil, grease and cleaning solvent in a closed, labelled container for proper disposal; never pour them on the ground, into a drain or near a water source
- Send worn metal parts for scrap
| Fault | Symptom | Likely Cause |
|---|---|---|
| Low pressure output | Weak spray or slow cylinder movement | Worn gear teeth or bearings |
| Noisy operation | Grinding or knocking sound | Lack of lubrication or damaged bearings |
| Leakage at cover | Fluid seeping from housing joint | Failed gasket or loose bolts |
| Pump seizes | Shaft will not turn | Debris blocking gears or dried-up seals |
| Overheating | Pump casing too hot to touch | Restricted inlet, blocked outlet, or wrong fluid |
A small-scale rice farmer near Mbeya relies on his tractor to prepare his fields before the rains. If the hydraulic gear pump on the tractor begins to leak oil and lose pressure, so that the plough lifts slowly, he can open the pump himself using a basic tool kit, replace the gasket and worn seals, and reassemble it to restore full pressure — saving the cost of calling a mechanic and keeping his tractor working during a critical planting window when every day of delay reduces his harvest.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret drawings.
- Select tools and equipment.
- Inspect gear type pump.
- Dismantle gear pump.
- Identify defects.
- Service gear type pump.
- Assemble gear type pump.
- Observe safety precautions.
- Test gear type pump.
- Clean tools, equipment and work place.
- Store tools and equipment.
Tathmini ya matokeo
Disassembled and assembled gear type pumps performed conforms to technical Specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: Students should explain how to:
- Disassemble and assemble gear type pumps.
Principles: Students should explain the principle of:
- Dismantling of gear pumps.
- Servicing the gear pumps.
- Assembling of gear pumps.
Theories: Students should explain:
- Important of Disassembling and assembling gear type pumps.
- Procedure of Disassemble and assemble gear type pumps.
- Safety precautions on dismantling and assembly of gear type pumps.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing service of gear type pumps.
- Safe handling of working tools and equipment.
- Waste disposal.
Swali
Before removing the cover plate of a gear type pump, a mechanic should use a scribe to draw alignment marks. What is the purpose of these marks?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado