Mada za sehemu hiiServicing submersible pumpsMada 2
- Servicing submersible pumps
- Dismantling and assembling submersible pumps
A submersible pump is a hydraulic machine that operates underwater to lift water from deep wells or boreholes for irrigation and other agricultural purposes. Servicing means safely dismantling the pump for inspection and reassembling it correctly so that it works efficiently afterwards.
- Submersible pump: A water pump designed to operate while fully submerged in water, placed deep inside a well or borehole.
- Dismantling: The process of carefully taking apart a pump to access its internal components for inspection, cleaning, or repair.
- Assembling: The process of putting all pump components back together correctly after servicing.
- Dry running: Running the pump with no water around it. A submersible pump is cooled and lubricated by the water it sits in, so it must never be run dry.
- Motor housing: The outer casing that protects the electric motor inside the pump.
Before dismantling or assembling any pump, follow these safety rules:
- Wear protective clothing: overalls, safety boots, gloves, safety goggles, and helmet
- Disconnect the power supply before starting any work
- Make sure the pump is removed from the water and placed on a stable work surface
- Keep the work area clean and free of oil or water spills
- Use tools only for their intended purpose
- Work with a partner when lifting heavy components
- Tool kit (spanners, screwdrivers, pliers)
- Grease gun
- Oil can
- Service manual for the specific pump model
- Lifting and lowering tools
- Hacksaw
- Tripod stand and chain block
- Pipe clamp
- Bench vice
- Multimeter
- Wheelbarrow
- Try square
- Tap and dies
- Hand grinder
- Gaskets and sealing rings (replacement)
Follow these steps carefully when dismantling a submersible pump:
-
Disconnect power supply — Switch off and unplug the pump from the electricity source to prevent electric shock.
-
Remove the pump from the well — Use the tripod stand and chain block to safely lift the pump out of the borehole. Lower it carefully onto a stable workbench.
-
Secure the pump in a vice — Clamp the pump housing firmly in a bench vice to prevent it from moving during dismantling.
-
Remove the discharge pipe — Unscrew the discharge pipe connection from the pump outlet using appropriate spanners.
-
Remove the motor housing — Unscrew the bolts holding the motor housing to the pump head. Carefully separate the motor housing from the pump body.
-
Inspect and remove the impeller — Unscrew the impeller from the shaft. Check the impeller for wear, cracks, or damage.
-
Remove the mechanical seal — Carefully pry out the mechanical seal from its housing. This seal prevents water from entering the motor.
-
Inspect internal components — Examine the shaft, bearings, and seals for wear, corrosion, or damage. Note any parts that need replacement.
-
Clean all components — Use clean water and a brush to remove mud, sand, and debris from all parts. Allow parts to dry completely.
Reassemble the pump by following these steps in order:
-
Replace worn components — Install new gaskets, seals, and any damaged parts identified during inspection.
-
Lubricate bearings — Apply fresh grease to the bearings using a grease gun. Oil moving parts with an oil can where required.
-
Install the mechanical seal — Press the new mechanical seal carefully into position, ensuring it sits flush and faces the correct direction.
-
Reassemble the impeller — Screw the impeller back onto the shaft securely. Turn the shaft by hand to check that the impeller rotates freely without rubbing.
-
Rejoin the motor housing — Place the motor housing back onto the pump body. Insert and tighten all bolts evenly in a criss-cross pattern to ensure even sealing.
-
Attach the discharge pipe — Screw the discharge pipe back into the pump outlet. Use PTFE thread-seal tape or jointing compound to prevent leaks.
-
Check all connections — Verify that all bolts, screws, and pipe connections are tight and properly secured.
-
Inspect the power cable — Check the cable and its joint for cuts or damaged insulation. Never lift or lower the pump by its cable.
Before lowering the pump back into the borehole, test it in a drum or tank of clean water with the pump fully covered. Never run a submersible pump dry, because it overheats and the seals are damaged:
- Connect the power supply temporarily
- Run the pump for 2–3 minutes
- Check that water is discharged strongly from the outlet and that the pipe joints do not leak
- Verify that the motor runs smoothly without unusual noise or vibration
- Before connecting power, use a multimeter to check the motor windings for continuity and that there is no connection between the windings and the pump body; during the test, check that the supply voltage is correct
If any problem is detected, switch off immediately and re-check the assembly.
A farmer in Morogoro has a submersible pump that has stopped delivering water. The pump was lifted from a 60-metre borehole, dismantled, and the following problems were found:
- The mechanical seal was cracked, allowing sand to enter the motor
- The impeller was worn on one side
Solution steps:
- The old mechanical seal was removed and a new one installed
- The worn impeller was replaced with a new impeller of the same size
- All bearings were cleaned and greased
- The pump was reassembled following the correct sequence
- The pump was tested in a drum of clean water before lowering back into the borehole
After reassembly, the pump was lowered back and reconnected. It now delivers water reliably at a rate of 2,000 litres per hour for irrigating the farmer's tomato crop.
- Clean and dry all tools and equipment and tidy the workplace
- Return tools to the tool kit and store lifting equipment properly
- Put old seals, gaskets and oily rags in the waste bin and collect used oil or grease for proper disposal. Keep all waste away from the well
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| Pump does not start | Power supply disconnected | Check and reconnect power |
| Water leakage at seals | Worn or damaged seals | Replace seals and gaskets |
| Low water output | Worn or blocked impeller | Clean or replace the impeller |
| Unusual motor noise | Dry running or bearing damage | Lubricate bearings or replace them |
| Motor overheats | Incorrect voltage or blockage | Check voltage supply and clear blockages |
In many rural villages of Tanzania, smallholder farmers depend on submersible pumps to draw water from deep boreholes for irrigating crops such as rice, maize, and vegetables. When a pump develops faults, a farmer in Kibaha or Mkuranga can save the cost of calling a mechanic by learning to dismantle the pump, identify the faulty seal or worn impeller, replace the parts, and reassemble it — restoring water supply to their shamba at minimal expense.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret drawings.
- Select tools and equipment.
- Inspect submersible pumps.
- Dismantle submersible pumps.
- Identify defects.
- Service submersible pumps.
- Assemble submersible pumps.
- Observe safety precautions
- Test submersible pumps.
- Clean tools, equipment and workplace.
- Store tools and equipment.
Tathmini ya matokeo
Dismantle and assemble pump conforms to technical Specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: Students should explain how to:
- Dismantle and assemble pump.
Principles: Students should explain the principles of:
- Dismantling submersible pumps.
- Servicing submersible pumps.
- Assembling submersible pumps.
Theories: Students should explain:
- Important of Disassemble and assemble submersible pumps
- Procedure of Disassemble and assemble submersible pumps
- Safety precautions on dismantling and assembly of submersible pumps.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while dismantling and assembly of submersible pumps.
- Safe handling of working tools and equipment.
- Waste disposal.
Swali
Which of the following is the FIRST step to take before dismantling a submersible pump?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado