Mada za sehemu hiiPerforming maintenance of wind millsMada 4
- Checking and repairing windmill gear box
- Checking and replacing leather cups
- Checking and replacing drive rods
- Performing maintenance of windmill tower
A leather cup is a flexible seal fitted inside the pump cylinder of a windmill. It creates a watertight seal between the piston and cylinder walls, allowing the windmill to lift water from a borehole or well. Over time, leather cups wear out, crack, or harden, and must be checked regularly and replaced to keep the windmill working efficiently.
Leather cups are cup-shaped seals made from treated leather. In a windmill water pump:
- They are attached to the piston rod
- They move up and down inside the pump cylinder
- As the piston moves up, the leather cup expands against the cylinder wall, pushing water upward
- As the piston moves down, the valve in the piston opens and water passes through to the space above the cup
Good leather cups ensure the pump creates strong suction to draw water from depth.
Regular checking prevents:
- Water leaks inside the pump
- Loss of pumping efficiency
- Complete pump failure
- Wasted wind energy
Follow these steps to inspect leather cups on a windmill:
- Stop the windmill — turn the wheel out of the wind (furl it), apply the brake and tie the wheel so it cannot rotate
- Disconnect the pump rod from the windmill and open the top of the pump
- Lift out the pump rod and piston with the leather cup assembly, using the tripod stand and chain block when the cylinder is down a borehole
- Visually inspect the leather cup for:
- Cracks or splits in the leather
- Hardening or stiffness (the leather should be soft and pliable)
- Worn edges or thinning sections
- Signs of drying out or crumbling
- Test flexibility by bending the leather gently — it should flex without cracking
- Check the seating groove where the leather cup fits onto the piston for wear or damage
- Measure the cup diameter against the service manual specifications using calipers or a measuring tape
Example: A windmill serving a village water supply near Mwanza has been pumping less water each day. Upon inspection, the leather cup shows visible cracks along its rim. This indicates the cup must be replaced before the pump fails completely.
- Service manual (for specifications)
- Tool kit (spanners, wrenches)
- New leather cup (correct size)
- Grease gun
- Oil can
- Clean rags
- Safety goggles and gloves
- Tripod stand, chain block and pipe clamp for lifting and holding the pump rods
Step 1: Preparation
- Stop the windmill and lock out the mechanism
- Disconnect the pump rod from the windmill and lift the rods and piston out of the borehole with the tripod stand and chain block, clamping the rod with a pipe clamp at each lift so it cannot fall back
- Clean the exterior of the pump head
Step 2: Remove the Old Leather Cup
- Unscrew and remove the pump head cover
- Grip the piston rod with a pipe clamp or bench vice
- Unscrew the cup holder or gland nut holding the leather cup in place
- Slide the worn leather cup off the piston rod
- Inspect the groove on the piston for rust or debris — clean it thoroughly
Step 3: Fit the New Leather Cup
- Soak the new leather cup in clean water until it is soft and pliable (follow the time given in the service manual)
- Apply a thin coat of compatible lubricant (as specified in the service manual) to the leather
- Slide the new leather cup onto the piston rod, ensuring it sits correctly in the groove
- Secure it with the cup holder or gland nut, tightening evenly
- Check that the leather cup sits squarely and has even contact all around
Step 4: Reassemble and Test
- Reinsert the piston rod into the pump cylinder
- Reconnect the pump rod to the windmill, refit the pump cover and tighten all bolts securely
- Apply grease to the moving parts using the grease gun
- Release the lock and allow the windmill to turn slowly
- Observe the pumping action — water should flow steadily
Step 5: Record the Work
Note the date, the condition of the old cup, and the new cup installation in a maintenance log book.
Step 6: Clean Up and Store
- Clean the tools, wipe up oil and grease and tidy the work area
- Return tools and lifting equipment to the store
- Put the old leather cup and oily rags in the waste bin. Do not leave them near the well, where they could pollute the water
| Fault | Cause | Remedy |
|---|---|---|
| Leather cup hard and cracked | Age, lack of lubrication | Replace the cup; lubricate regularly |
| Water leaking past the cup | Worn or damaged seal | Replace the leather cup |
| Pump losing suction | Loose cup or wrong size | Check fit and replace if necessary |
| Cup slipping on piston | Worn groove or loose holder | Repair groove or replace holder |
- Always lock out the windmill before maintenance
- Wear safety goggles, gloves, a helmet and safety boots throughout the work
- Use gloves when handling lubricating oils
- Stand the tripod on firm ground, check the chain block before lifting, and keep hands and feet clear of the rods; use a safety harness if you must climb the tower
- Follow the service manual for torque settings
In rural Singida, a farmer uses a windmill to pump water from a 40-metre borehole to irrigate vegetables. After three years, the pump output drops noticeably. Checking the leather cup reveals it has hardened and cracked. Replacing the leather cup costs far less than a new pump and restores full pumping capacity, saving the farmer from having to buy water during the dry season.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret drawings.
- Select tools and equipment.
- Inspect wind mill.
- Identify defects.
- Check replacing leather cups
- Service wind mill.
- Observe safety precautions
- Clean tools, equipment and work place.
- Store tools and equipment.
Tathmini ya matokeo
Serviced wind mill conforms to technical Specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: Students should explain how to Check and replace leather cups
Principles: Students should explain the principle of:
- Checking and replacing leather cups
Theories: Students should:
- Describe procedures for checking and replacing leather cups
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while servicing wind mill.
- Safe handling of working tools and equipment.
- Waste disposal.
Swali
What is the primary function of a leather cup in a windmill water pump?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado