Mada za sehemu hiiDesigning farm workshop layoutMada 3
- Outlining workshop service bay
- Designing layout of light-duty equipment
- Designing layout of heavy-duty equipment
Heavy-duty equipment in a farm workshop means the large, heavy things: tractors and combine harvesters brought in for repair, and fixed machines such as a hydraulic press, a pillar drill, a power hacksaw, a welding plant and a compressor. Because they are big, heavy and powerful, where they stand decides how safely and easily everyone can work.
- A strong, level concrete floor that can carry the weight
- A high, wide door and a clear driveway, so that a tractor can drive in and out without reversing round corners
- Service bays long and wide enough for the largest machine, with working space all round it
- Lifting equipment such as a gantry, chain block or strong jack, and stands to support what has been lifted
- Good ventilation, because engines are run inside
- A power supply and good lighting where the machines stand
- Follow the flow of work. A machine should move in one direction: reception, washing, repair bay, testing, collection.
- Group related work. Engine work, welding, tyre work and the tool store each have their own section.
- Shortest movement. The heaviest and most frequent jobs are nearest the door and nearest the tools they need.
- Keep hazards apart. Welding and grinding, which throw sparks, are kept away from fuel, oil, paint and tyres.
- Leave space. Gangways and the space around every machine are kept clear and are marked on the floor.
- Allow for growth. Leave room for a machine the workshop may get later.
| Section | Where it goes |
|---|---|
| Reception and parking | Outside, near the gate |
| Washing bay | Outside, with a drain and an oil trap |
| Heavy repair bays | Directly behind the main door |
| Machine shop (press, pillar drill, power hacksaw) | Along one wall, near the power supply |
| Welding bay | In a corner with screens, an outside wall and good ventilation |
| Tool store and spares store | Central, beside the supervisor's office |
| Fuel, oil and gas store | A separate, ventilated, locked room or cage away from sparks |
| Waste oil and scrap | Outside, at the back, under cover |
- Foundation: a heavy machine stands on a concrete base strong enough for its weight and vibration
- Levelling: the machine is set level with a spirit level, using packing pieces or levelling screws
- Anchoring: it is fixed down with anchor bolts so that it cannot move or tip
- Clearance: space is left all round for the operator, for long workpieces and for maintenance, and the machine is turned so that the operator faces the gangway and has good light
- Power: the supply has its own isolating switch within reach of the operator, the cables are protected, and the machine is earthed
- Guards and emergency stop: all guards are fitted and the stop button is tested before the machine is used
Always follow the installation drawing and instructions in the maker's manual.
- List the equipment and vehicles the workshop must handle, with the length, width, height and weight of each
- Measure the building and draw it to scale, for example 1 cm on paper for 1 m on the ground, showing doors, windows, columns and power points
- Cut out paper shapes of each machine and bay to the same scale
- Mark the driveway and the main gangways first
- Place the heavy repair bays, then the fixed machines, then the stores
- Check the flow of work, the clearances and the distance between sparks and fuel
- Add the tool storage, security, safety equipment, signs and waste points
- Discuss the plan with the people who will use it, correct it, and draw the final layout
- Heavy tools such as jacks, stands and chain blocks are kept on the floor or on low shelves next to the bays where they are used
- Hand tools hang on shadow boards, where a painted outline shows at once which tool is missing
- Special tools are kept in the tool store and issued against a record
- One lockable tool store with one person in charge of the key and the issue book
- Strong doors, window bars and outside lighting
- Every machine and tool marked with a number and entered in the inventory
- A fence and a lockable gate round the yard
- Fire extinguishers and sand buckets at the doors and near the welding bay
- A first aid box that everyone can reach
- At least two exits, kept clear
- Guards on all machines, and stands under every raised load
- Safety gear for each job: helmet, goggles, gloves, overall, boots, ear protection
- Fans or open sides to remove exhaust and welding fumes
| Colour and shape | Meaning | Example |
|---|---|---|
| Red circle with a line through it | Do not | No smoking |
| Yellow triangle | Warning | Overhead load, moving parts |
| Blue circle | You must | Wear eye protection |
| Green rectangle | Safe condition | Exit, first aid |
- Paint yellow lines on the floor for gangways and round each machine and bay
- Put each sign at the hazard it refers to, at eye level
- Put a poster with the operating instructions next to each machine
- Label every container and shelf of fuel, oil, gas, paint and chemicals with what it holds and its danger
- Lift heavy parts with lifting equipment, never by hand alone
- Collect used oil in closed drums for recycling; never pour it on the ground or into a drain
- Lead washing water through an oil trap
- Keep scrap metal, old tyres, batteries and general rubbish in separate, marked places
- Place noisy machines away from offices and neighbours, and keep dust and smoke out of the building with good ventilation
- Clean the drawing instruments after the design work and store them and the drawings in a dry place
A farm workshop building is 12 m long and 10 m wide, with a door 4 m wide and 4 m high in the middle of one short wall. It must take one tractor at a time and has a pillar drill, a hydraulic press and a welding set.
- Driveway: a strip 4 m wide runs straight in from the door
- Repair bay: the first 6 m of that strip is the bay, 6 m long by 4 m wide. A tractor about 4 m long and 2 m wide then has 1 m clear on each side and at each end.
- Space left: 3 m on each side of the bay, and 6 m behind it
- Machine shop: the pillar drill and the press stand against the left wall, each with at least 1 m clear round it
- Tool store and office: on the right side, next to the bay, with a shadow board facing the bay
- Welding bay: in the back left corner, behind a screen, beside a window
- Oil and gas store: a locked cage in the back right corner, far from the welding bay
- Outside: washing bay with an oil trap at the front, waste oil drums and scrap at the back
- Signs and marks: yellow lines round the bay and the machines; fire extinguishers at the door and the welding bay; a second exit door in the back wall
When a village buys a tractor, the first breakdown often happens in a shed where nothing can be lifted and tools cannot be found. A workshop laid out for heavy equipment lets the mechanic drive the tractor in, lift and support it safely, reach every tool in a few steps and finish the repair in days instead of weeks.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Plan workshop layout heavy-duty equipment.
- Arrange tools.
- Design security system of tools and equipment.
- Design layout of heavy-duty equipment
- Design and implement safety system to workers.
- Identify marks and postures.
- Place sign mark and postures.
- Label safety precautions for workshop materials and goods.
Tathmini ya matokeo
Workshop layout heavy-duty equipment conforms to environmental and labor rules and Regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Arrange different workshop sections for heavy-duty equipment.
Principles: Students should explain the principle of:
- Laying out workshop.
- Machine installation in workshop.
Theories: Students should explain:
- Steps to design workshop layout for heavy duty equipment.
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools and equipment.
- Environmental impacts.
Swali
What does a blue circle safety sign mean in a workshop?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado