Mada za sehemu hiiPerforming filingMada 3
- Performing flat filing
- Performing radii filing
- Performing angle filing
Flat filing is a bench work skill used to smooth and level surfaces on metal, wood, or plastic workpieces using a flat file. This skill is essential for removing imperfections and achieving a flat, even finish before further processing or assembly.

Filing is the process of removing material from a workpiece by rubbing it with a file — a hand tool with sharp teeth on its surface. The file cuts away small amounts of material each time it is pushed or pulled across the workpiece.
There are two main filing methods:
- Cross filing — The file is moved diagonally across the workpiece. This method removes material quickly and is used for rough shaping and removing large amounts of material.
- Draw filing — The file is moved straight back and forth along the length of the workpiece. This method produces a smoother finish and is used for final finishing operations.
Before performing flat filing, gather the following tools and equipment:
- Flat files — The main tool for flat filing. Flat files have a rectangular shape with teeth on both flat sides.
- File card — A brush with stiff wire bristles used to clean debris from the file teeth after use.
- Try square — Used to check if the workpiece surface is flat and square.
- Steel rule — For measuring dimensions.
- Centre punch and scriber — For marking lines on the workpiece.
- Work bench and vice — To hold the workpiece securely.
- Chalk — To coat the workpiece surface so you can see where you are filing.
Flat filing involves using a flat file to remove excess material from a workpiece until the surface becomes flat, even, and smooth. The goal is to eliminate high spots and create a uniformly flat surface.
Flat files come in different types:
- Flat files — Standard rectangular files for general flat filing
- Hand files — Tapered slightly toward the point
- Bastard files — Medium-coarse teeth for rapid material removal
- Square files — Square cross-section for flat surfaces
When selecting a material for filing, consider these properties:
- Hardness — The workpiece should not be too soft (it will clog the file) or too hard (it will wear the file quickly).
- Wear resistance — The material should not damage the file teeth rapidly.
- Machinability — How easily the material can be cut or filed.
- Dimensional stability — The material should hold its shape during filing.
The following materials are commonly filed in workshop settings:
- Metals — Steel, aluminum, brass, and copper
- Wood — Various types used in carpentry
- Plastic — Acrylic, PVC, and other plastics
- Composites — Materials like fiberglass
Follow these steps to perform flat filing correctly:
Step 1: Prepare the Workpiece
Mark out and cut the material to the required size. For practice, use a flat bar measuring 50 mm × 6 mm × 60 mm. Clamp the workpiece in the vice with the largest flat surface facing upward.
Step 2: Remove the Scale
Before flat filing, remove the scale (dark coating) from the metal surface. Use an old or worn file for this step, as the scale is abrasive and can damage a new file. Apply pressure to the front of the file and scrape the scale off.
Important: Never touch the cleaned surface with your bare hand. Oil from your skin will cause the file to slide instead of cutting.
Step 3: Locate High Spots
Place the flat file on the workpiece surface. Apply pressure with your thumb to feel where the high spots are. Move the file handle about 100 mm left and right to check for pivoting. When you find a high spot, you will see witness marks on the material below your thumb.
Step 4: Mark and Check
Remove the workpiece and hold it up against the light to check for high spots. Use a try square in four directions to check flatness. Mark the high spots with a marker, then coat the entire face with chalk. The chalk helps you see where you are filing.
Step 5: File the High Spots
Place the file directly on the marked high spot. Apply pressure with your left-hand thumb (for right-handed users) on that spot. Push and pull the file approximately 10 mm in length to remove the material.
Important: Do not apply pressure with your right hand only — this causes a rocking motion that creates a curved (convex) surface instead of a flat one.
Step 6: Check Progress Frequently
Remove the file frequently and check the workpiece with a try square. Three-quarters of the face must be in contact with the square blade to confirm flatness.
Step 7: Repeat Until Flat
Repeat the filing and checking process until the workpiece is completely flat on one side.
Always wear appropriate safety gear when performing flat filing:
- Safety clear glasses to protect your eyes
- Gloves to protect your hands
- Safety boots to protect your feet
- Overall or protective clothing
A student needs to flat file a steel bar that is 60 mm long, 50 mm wide, and 6 mm thick. After initial cutting, the bar has high spots on the 50 mm × 60 mm face. The student marks the high spots with chalk and begins filing.
Problem: The student applies pressure only with the right hand while filing. What will happen?
Solution: Applying pressure only with the right hand causes a rocking motion. This makes the file pivot on one edge, producing a convex (curved) surface instead of a flat surface. To avoid this, the student must bend over the workpiece to see under the file and apply balanced pressure with both hands, with the left thumb pressing on the high spot.
In Tanzania, flat filing is used by metalworkers and carpenters in small workshops across towns like Arusha, Mwanza, and Dodoma when repairing farming tools such as machetes and hoes, or when shaping metal parts for bicycle and motorcycle repairs. A local technician at a jua kali workshop might flat file a piece of steel to create a flat mounting plate for an electrical box, ensuring it sits evenly against a wall before being secured.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select tools and equipment
- Take measurements and marking
- File work piece
- Check accuracy
- Observe safety precautions
- Clean tools, work piece and workplace
- Store tools, equipment and work piece
Tathmini ya matokeo
Filed/ground work piece conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence: Detailed knowledge of:
Method used: The student should explain how to:
- Mark work piece
- File a work piece
- Grind work piece
Principles: The student should explain the principles of:
- Taking measurements
- Marking work piece
- Filing and grinding work piece
Theories: The student should:
- Identify different types of materials and their properties
- Explain applications of different materials
- Describe proper use of files and equipment
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions pertaining to filling/grinding
- Safe handling of working tools and equipment
- Waste disposal
Swali
What is the primary purpose of flat filing in bench work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado