Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Counterboring drilled holes
Carrying Out Drilling on Bench Drilling Machine
A bench drilling machine (also called a bench drill press) is a stationary power tool used to create precise holes in various materials. It provides stability and accuracy that hand drilling cannot match, making it essential for workshop tasks that require repeatable, high-quality holes.
A bench drilling machine consists of several main parts that work together:
- Base – provides stability and support for the entire machine
- Column – vertical pillar that holds the head and allows height adjustment
- Worktable – flat surface where the workpiece is placed; can be adjusted up or down
- Head – contains the motor, spindle, and drill chuck
- Drill chuck – holds the drill bit securely in place
- Feed lever – used to lower and raise the drill bit during drilling
- Speed adjustment – allows selection of appropriate drilling speed
- Depth stop – controls how deep the drill bit goes into the material

1. Wear Protective Gear
Before starting, put on safety glasses to protect your eyes from flying debris. Wear gloves to protect your hands, and use safety boots for foot protection.
2. Select Tools, Equipment, and Drill Bit
Choose a drill bit that matches the material you are drilling. For metal, use high-speed steel (HSS) twist drills. For wood, use wood-boring bits. The drill bit must be slightly smaller than the hole size you need.
3. Insert the Drill Bit
Loosen the drill chuck, insert the selected drill bit into the chuck, and tighten securely. Make sure the bit is straight and firmly held.
4. Adjust Speed and Depth
Set the appropriate speed based on the material and drill bit size. Smaller bits require higher speeds; larger bits need slower speeds. Set the drilling depth using the depth stop on the machine.
5. Secure the Workpiece
Place the workpiece on the worktable. Use clamps to secure it firmly. This prevents the material from moving during drilling, which could cause inaccurate holes or injury.
6. Position the Workpiece
Align the marked drilling location directly under the drill bit. Use a try square or scriber to ensure proper alignment.
7. Start the Drill Press
Turn on the machine using the on/off switch. Let the motor reach full speed before proceeding.
8. Drill the Hole
Lower the drill bit gradually using the feed lever. Apply steady, even pressure. Do not force the drill—let the bit cut at its own pace. Pause occasionally to clear chips and debris.
9. Complete the Hole
Continue drilling until you reach the desired depth. Then raise the drill bit using the feed lever.
10. Inspect and Finish
Remove the workpiece and check the hole for rough edges or burrs. Use a deburring tool or sandpaper to smooth edges if needed.
11. Clean Up
Remove all debris from the machine and work area. Clean the drill bit and store it properly.
A student needs to drill three evenly spaced holes along a metal strip that is 12 cm long. The first hole should be 2 cm from the left edge, and the remaining holes should be spaced 3 cm apart.
Solution:
- First hole position: 2 cm from left edge
- Second hole position: 2 cm + 3 cm = 5 cm from left edge
- Third hole position: 5 cm + 3 cm = 8 cm from left edge
Therefore, the three hole positions are at 2 cm, 5 cm, and 8 cm from the left edge.
- Always wear safety glasses when operating the machine
- Secure all workpieces with clamps before drilling
- Keep hands away from moving parts
- Turn off the machine when changing drill bits
- Never leave the machine running unattended
In Tanzania, bench drilling machines are commonly used in vocational training workshops and small metalworking shops. For example, a technician at a garage in Dar es Salaam might use a bench drill press to create holes in metal brackets when fabricating shelf supports for a customer's storage cabinet. The precise holes allow bolts or screws to fit securely, ensuring the shelf is sturdy and safe for holding items in homes, shops, or warehouses.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select tools, equipment and materials
- Mark work piece
- Perform drilling
- Observe safety precautions
- Clean tools, equipment and workplace
- Store tools, equipment and work piece
Tathmini ya matokeo
Drilled hole conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Mark a work piece
- Drill a work piece
Principles: The student should explain the principles of:
- Taking measurements
- Marking work piece
- Drill work piece
Theories: The student should:
- Identify different types of materials and their properties
- Explain applications of different materials
- Describe proper use equipment
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions pertaining to filling/grinding
- Safe handling of working tools and equipment
- Waste disposal
Swali
A bench drilling machine is also known as a:
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado