Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series resistive circuit
- Building parallel resistive circuit
- Building combination circuit
Parallel Resistive Circuit
A parallel resistive circuit is an electrical circuit where two or more resistors are connected across the same two points, creating multiple paths for current to flow. In this arrangement, each resistor connects directly across the power source, meaning every component receives the same voltage.
- Same voltage: The voltage across each resistor in a parallel circuit is the same and equals the source voltage.
- Different current: The current divides among the different branches. Each branch current depends on the resistance of that branch.
- Total current: The total current flowing from the power source equals the sum of the currents through each branch.
- Total resistance: The total resistance is always less than the smallest individual resistor.
Materials Required
- Power supply (battery or DC source)
- Two or more resistors (e.g., 100Ω and 200Ω)
- Connecting wires
- Switch
- Multimeter
Connection Steps
- Identify the terminals of each resistor (no polarity for resistors).
- Connect one end of the first resistor to the positive terminal of the power supply.
- Connect the other end of the first resistor to one end of the second resistor.
- Join the free end of the second resistor to the negative terminal of the power supply.
- Verify that both resistors have both ends connected across the same two points (the source terminals).
Set your multimeter to the DC voltage (V~) setting:
- Connect the red probe to the point where current enters a resistor.
- Connect the black probe to the point where current leaves the same resistor.
- Record the voltage reading.
- Repeat for each resistor.
In a properly connected parallel circuit, you will find that the voltage across each resistor is exactly the same — equal to the supply voltage.
To measure current, you must break the circuit and connect the multimeter in series:
- Disconnect one wire from the circuit.
- Set the multimeter to DC current (A~) mode.
- Connect the multimeter probes in series with the circuit.
- For branch current, measure through each individual resistor.
- For total current, measure at the main wire before it splits.
For resistors in parallel, use the formula:
Rtotal1=R11+R21+R31
Or, for two resistors only, use the shortcut:
Rtotal=R1+R2R1×R2
A Tanzanian student builds a parallel circuit with a 6V battery, a 100Ω resistor (R₁), and a 200Ω resistor (R₂).
Step 1: Draw the circuit
- Both resistors connected directly across the 6V battery terminals.
Step 2: Calculate total resistance
Rtotal=100+200100×200=30020,000=66.7Ω
Step 3: Calculate total current
Using Ohm's Law: I=RV
Itotal=66.7Ω6V=0.09A=90mA
Step 4: Calculate branch currents
- Current through R₁: I1=100Ω6V=0.06A=60mA
- Current through R₂: I2=200Ω6V=0.03A=30mA
Step 5: Verify total current
Itotal=I1+I2=60mA+30mA=90mA
This confirms the parallel circuit rule that total current equals the sum of branch currents.
- Always wear safety goggles and gloves when working with electronic components.
- Ensure the power supply is turned off before making or changing connections.
- Do not touch bare wires while the circuit is powered.
- Report any damaged equipment immediately to your teacher.
- Connecting multimeter in voltage mode across a component while set to current mode, which can damage the meter.
- Forgetting to turn off the power before rearranging the circuit.
- Measuring voltage in series instead of parallel.
In Tanzania, parallel circuits are commonly used in household wiring. When you plug in a phone charger, a radio, and a lamp into different wall sockets, each device is connected in parallel to the 230V mains supply. This ensures that each device receives the full 230V voltage and can operate independently — if one device stops working, the others continue to function normally. This is why your phone charger still works even when the radio is switched off.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret circuit diagram
- Select tools, equipment and material
- Select components
- Construct parallel resistive circuit
- Solder constructed circuits
- Test the built circuits
- Clean tools, equipment and workplace
- Store tools, equipment and materials
Tathmini ya matokeo
Constructed circuits function as per technical specifications.
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain how to:
- Build a simple circuit
- Build parallel circuits
Principles: The student should explain the principle of:
- Parallel resistive circuits
Theories: The student should explain:
- Different types of circuits
- Application of parallel resistive circuit
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions during circuit building
- Safe handling of tools and equipment
Swali
What is a key characteristic of resistors connected in parallel?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado