Mada za sehemu hiiConstructing capacitive circuitsMada 4
- Building single capacitor circuit
- Building series inductive circuit
- Building parallel capacitive circuits
- Building combination circuit
Series Inductive Circuit
An inductive circuit is an electrical circuit that contains an inductor (also called a coil or choke). An inductor is a component made of wire wound into a coil that stores energy in a magnetic field when electric current flows through it. The property of an inductor that opposes changes in current is called inductance, measured in Henries (H).
When an inductor is connected in a series with other components like a resistor and a power source, it forms a series inductive circuit. In this arrangement, the same current flows through all components.
Inductance
- Inductance is the ability of a coil to resist changes in current flow
- When current increases, the magnetic field expands and induces a voltage that opposes the change
- When current decreases, the magnetic field collapses and induces a voltage that tries to keep the current flowing
Series Circuit Rules
In a series circuit:
- Same current flows through all components (Itotal=I1=I2=...)
- Total voltage is the sum of individual voltage drops (Vtotal=V1+V2+...)
- Total resistance is the sum of all resistances (Rtotal=R1+R2+...)
Components Required
- Power source (DC power supply or battery)
- Inductor (inductance coil)
- Resistor
- Connecting wires
- Multimeter
- Electronics board
Steps to Build
-
Connect the inductor (L) and resistor (R) in series — join one end of the inductor to one end of the resistor using a connecting wire
-
Connect the power source — attach the free end of the inductor to the positive terminal and the free end of the resistor to the negative terminal of the power supply
-
Set up measurement instruments — connect the multimeter in series with the circuit to measure current, or in parallel across components to measure voltage drops
-
Apply power and observe — switch on the power supply and observe the readings on the multimeter
Measuring Current and Voltage
- Total current (I): Connect the multimeter in series with the circuit (set to DC mA or amps)
- Voltage across inductor (VL): Place multimeter probes across the inductor terminals
- Voltage across resistor (VR): Place multimeter probes across the resistor terminals
The sum of VL and VR should equal the supply voltage (Vsupply).
A series inductive circuit is connected to a 12 V DC power supply. The inductor has an inductance of 0.5 H, and the resistor has a resistance of 100 Ω. If the current flowing through the circuit is measured as 0.08 A:
Calculate:
- Total resistance in the circuit
- Voltage drop across the resistor
Solution:
-
Using Ohm's Law: Rtotal=IV=0.08 A12 V=150 Ω
-
Voltage drop across the resistor: VR=I×R=0.08 A×100 Ω=8 V
The remaining voltage (12 V−8 V=4 V) appears across the inductor as the inductive reactance.
- Always wear safety goggles and overall when working with electronics
- Wear safety boots to protect your feet from falling tools
- Ensure the work bench is clean and organized
- Always turn off the power supply before making or changing connections
- Handle the multimeter probes carefully to avoid short circuits
In Tanzania, series inductive circuits are found in radio and television receivers where inductors are used together with capacitors to tune to different frequencies. A technician repairing a radio in Dar es Salaam would use this knowledge to measure voltage drops across inductors and resistors on the circuit board, helping to identify faulty components. Understanding how inductors behave in series also helps in troubleshooting fluorescent lighting fixtures commonly used in shops and homes across the country, where inductors (chokes) control the current flowing through the tube.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret circuit diagram of capacitive circuit
- Select tools, equipment and material required
- Prepare capacitors and cables for termination
- Construct circuit on board
- Solder built circuits
- Test circuit
- Record test results
- Clean tools, equipment and workplace
- Store tools, equipment and materials
Tathmini ya matokeo
Constructed capacitive circuit functions as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Connect capacitors in series and parallel
- Solder capacitors
- Measure capacitance values
- Identify different capacitors
- Calculate value of capacitive reactance
Principles: The student should explain the principles of:
- Reading capacitor colour code
- Constructing capacitive circuits
- Measuring capacitance
Theories: The student should explain:
- Characteristics of capacitors
- Application of different types of capacitors
- Electrical symbols
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions in handling capacitors
- Safe handling of work tools and equipment
Swali
Which of the following is another name for an inductor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado