Mada za sehemu hiiConstructing inductive circuitsMada 5
- Building single inductor circuit
- Building series inductive circuit
- Building parallel inductive circuit
- Building combination circuit
- Testing inductive circuits
An inductor is an electronic component that stores energy in a magnetic field when electric current flows through it. It is made by winding a coil of wire around a core material (such as iron, ferrite, or air). The main role of an inductor in an electrical circuit is to resist changes in current flow — this property is called inductance, measured in Henries (H).
Inductors are used in many applications, including filters, radios, power supplies, and electric motors.
Real-life Examples of Inductors
- Radio receivers — inductors tune to different frequencies
- Power supplies — inductors smooth out fluctuating voltages
- Electric motors — inductors help control motor speed
- Phone chargers — inductors are found in the charging circuit
Before building, gather these components:
- An inductor (e.g., 10 mH to 100 mH coil)
- A DC power supply (battery or low-voltage adapter)
- A resistor (various values: 100Ω, 220Ω, 470Ω)
- Connecting wires
- Multimeter (analogue or digital)
- Electronics board or breadboard
Safety Gear
Always wear safety goggles and work boots when working with electronic circuits. Use an overall for protection.
Step 1: Plan the Circuit
Draw a simple circuit diagram showing the power supply, resistor, and inductor connected in series.
+ Battery → Resistor → Inductor → Battery -
Step 2: Insert the Inductor
Place the inductor on the electronics board or breadboard. Ensure the coil terminals are clean and making good contact.
Step 3: Connect the Resistor
Connect the resistor in series with the inductor. The resistor limits the current flowing through the circuit.
Step 4: Connect the Power Supply
Connect the DC power supply (or battery) to complete the circuit. Make sure the positive terminal connects to one end and the negative to the other.
Step 5: Check Connections
Double-check all connections to ensure they are secure and correct before turning on the power.
- Set the multimeter to measure DC current (mA) or resistance (Ω).
- Measure the current flowing through the circuit by placing the multimeter in series.
- Measure the voltage across the inductor and resistor using the voltage setting.
- Record your readings in a table.
If the circuit does not work, check for:
- Loose connections
- Damaged inductor (check for broken coil)
- Wrong polarity of power supply
Change the resistor value and observe what happens:
| Resistor Value | Current (mA) | Observation |
|---|---|---|
| 100 Ω | Higher | Bright LED or stronger effect |
| 220 Ω | Medium | Moderate effect |
| 470 Ω | Lower | Dimmer effect |
As the resistance increases, the current decreases. This shows that the resistor controls the amount of current in the inductor circuit.
A student builds a circuit with a 12 V battery, a 220 Ω resistor, and a 50 mH inductor.
Calculate the current flowing in the circuit.
Using Ohm's Law:
I=RV
I=220 Ω12 V=0.055 A=55 mA
The current flowing through the inductor circuit is 55 mA.
Now, if the student replaces the 220 Ω resistor with a 470 Ω resistor:
I=470 Ω12 V=0.0255 A≈26 mA
The current decreases to approximately 26 mA, demonstrating how changing the resistor value affects circuit behaviour.
- An inductor stores energy in a magnetic field and resists changes in current.
- A single inductor circuit is built by connecting an inductor, a resistor, and a power source in series.
- The resistor limits current and helps protect the inductor.
- Testing with different resistor values shows how resistance affects current flow.
- Always follow safety procedures when working with electronic circuits.
In Tanzania, inductors are used in radio receivers found in small businesses and homes. For example, a technician repairing a simple radio in Dar es Salaam would need to identify and test inductors in the tuning circuit to restore proper station selection. Understanding how inductors work also helps in maintaining phone chargers and LED lights commonly used in Tanzanian households, where faulty charging circuits often involve inductor failures.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret diagram of inductive circuit
- Select tools, equipment and material
- Prepare inductors and cables for termination
- Build inductor circuits
- Solder built circuits
- Test the built circuit
- Record test results
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Constructed inductive circuit conforms to electrical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Identify an inductor
- Connect inductors in series and parallel
- Measure values of inductance
- Calculate value of inductive reactance
Principles: The student should explain the principles of:
- Constructing inductive circuits
- Measuring inductance
Theories: The student should explain:
- Characteristics of inductors
- Application of different types of inductive circuits
- Electrical symbols
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions in inductive loads
- Safe handling of tools, equipment and inductors
Swali
What is the main property of an inductor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado