Mada za sehemu hiiConstructing low/high frequency circuitsMada 2
- Building low frequency circuit
- Building high frequency circuit
Building Low Frequency Circuits
A low frequency circuit is an electronic circuit designed to operate at frequencies below about 100 kHz. These circuits are commonly used in audio equipment, power supplies, timers, and filtering applications. They process signals that change slowly over time, such as audio waves or control signals.
Low frequency circuits use three basic passive components:
- Resistors – Limit current and divide voltage. They control how much current flows through different parts of the circuit.
- Capacitors – Store electrical energy in an electric field. In low frequency circuits, they are used for coupling signals, filtering, and timing.
- Inductors – Store energy in a magnetic field when current flows through them. They oppose changes in current and are used in filters and power applications.
Low frequency circuits are found in many everyday devices:
- Audio amplifiers and speakers
- Power supply filters (removing ripple from DC power)
- Timer circuits (flashing lights, delay switches)
- Tone controls in radios and music systems
- Battery charging circuits
1. Plan the Circuit
Before assembling, draw a simple circuit diagram. For example, a basic low frequency filter or amplifier stage using resistors and capacitors.
2. Gather Components and Tools
Collect the required components (resistors, capacitors, inductors if needed), wire, a breadboard or PCB, wire strippers, and a soldering iron if permanent connections are needed.
3. Ensure Safety
Put on your gloves, overcoat or overall, and boots. Make sure the power supply is turned off before making any connections.
4. Assemble the Circuit
- Place components on the breadboard or PCB in the positions shown in your circuit diagram.
- Connect wires carefully, ensuring positive and negative terminals are correct.
- Double-check all connections before powering the circuit.
5. Test and Measure
- Turn on the power supply.
- Use a multimeter to measure voltages at key points.
- Use an oscilloscope to observe the waveform if available.
- Record your measurements.
A low pass filter allows low frequency signals to pass while blocking high frequencies.
Circuit diagram: A resistor (R = 10 kΩ) in series with a capacitor (C = 0.47 μF), connected to an input signal and ground.
Calculating the cutoff frequency:
fc=2πRC1
Substituting the values:
fc=2π×10,000×0.47×10−61
fc=2π×0.00471=0.02951≈34 Hz
This means signals below 34 Hz pass through, while higher frequencies are reduced.
Practical test:
- Build the circuit on a breadboard.
- Connect a function generator to the input.
- Vary the input frequency from 20 Hz to 10 kHz.
- Use the oscilloscope to observe the output amplitude at different frequencies.
- Notice that the output decreases as the frequency increases above 34 Hz.
When you test your circuit, compare your measurements with expected values:
- Voltage levels – Do they match your calculations?
- Waveform shape – Is the output clean or distorted?
- Frequency response – Does the circuit behave as expected at different frequencies?
If the output is incorrect, check:
- Loose connections
- Wrong component values
- Polarity of polarized capacitors
- Always disconnect power before making changes.
- Wear protective gear at all times.
- Keep the workbench clean and organized.
- Never touch bare wires while the circuit is powered.
In Tanzania, low frequency circuits are used in community radio stations, public address (PA) systems in schools and churches, and in simple timer switches for streetlights. For example, a student might help repair a PA system at their school where the audio amplifier board has a faulty low frequency filter, using a multimeter to check voltage at the filter capacitors and replacing any damaged components to restore clear sound output.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select active electronic components
- Construct low frequency circuit
- Use test equipment
- Measure the circuit parameter
- Record measured results
- Observe safety precautions
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Measured circuit parameters conform to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct and test low frequency circuit
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments
- Testing electronic circuits
Theories: The student should explain:
- The difference between low and high frequency circuits
- Characteristics of low frequency circuits
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions in electronic work
- Safe handling of test equipment and measuring instruments.
Swali
According to the lesson, what is the upper frequency limit for a circuit to be considered low frequency?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado